background image

A manual valve be installed in an accessible location in the gas line external to the appliance for the
purpose of turning on or shutting off gas to the appliance.

Warning

Turn the knob counterclockwise to adjust the flame, size, so that the flame does not float out of

the container rim.
If need to adjust the flame size from big to small when operation, turn the knob counterclockwise 90
degrees to the position. (See Figure 13)

Figure 13

When you need to change the gas cooktop, you must first close the air supply valve and the cooktop
valve, unplug the plug of models with AC power supply, only after that you can remove the connector
hose or threaded connector and then move the gas cooktop.
Warn of the potential hazards associated with storage cabinet areas above appliances. Misoperation
can cause fire.

Save the orifices removed from the appliance for future use.

Gas Conversion Operating Instructions

Figure 14

Gas type

Propane

(Parts list)

NG

(Parts list)

Nozzles Dia. (mm)

Power (Btu/hr)

Quantity

Nozzles Dia. (mm)

Power (Btu/hr)

Quantity

Ultra rapid burner

1.10

13000

1

1.68

13000

1

Rapid burner

0.96

10200

1

1.57

10200

1

Semi rapid burner

0.76

6000

1

1.16

6000

1

Auxiliary burner

0.60

3800

1

0.91

3800

1

Washer

1

1

Connector nut

1

1

Barb connector for hose

1

1

13

Figure 15

NG

Propane

Содержание EMPV-24GC28




















Отзывы: