6
The reception of the DCF radio signal is affected by the following factors:
• Thick walls and insulation, basements and cellars.
• Inadequate local geographical conditions (these are difficult to assess in advance).
• Atmospheric disturbances, thunderstorms, electrical appliances with no interference elimination,
television sets and computers located near the DCF receiver.
If the weather station cannot detect the DCF signal, time and date must be set manually.
Note: If the weather station detects the DCF signal but the current time on the screen is incorrect
(e.g. shifted ±1 hour), you must set the correct time zone for the country where you are using the
station, see Manual Setting of Time and Date. The current time will be shown with the appropriate
time zone difference.
Manual Setting of Time and Date, 12/24 h Time Format, °C/°F Temperature Unit
1. Press and hold the MODE button for 3 seconds.
2. Use the UP or DOWN button to set the following parameters: year – month – day – date display
format – calendar language (GER, FRE, ITA, DUT, SPA, DAN, ENG) – 12/24 h time format – time
zone – hour – minute – °C/°F temperature unit.
Setting an Alarm
The weather station allows you to set 2 separate alarm times.
Press the ALARM button repeatedly to view the alarm time for alarm no. 1 (A1) or 2 (A2).
Then long-press the ALARM button; the time value will start flashing.
Set the time by repeatedly pressing the UP or DOWN button; to navigate in the menu, press the
ALARM button again.
You can set the time for both alarms this way.
To activate alarm no. 1 press the ALARM button 1× to display the time for alarm no. 1 (A1). Press UP
or DOWN; will appear on the screen.
To deactivate the alarm, press UP or DOWN again; the icon will disappear.
To activate alarm no. 2 press the ALARM button 2× to display the time for alarm no. 2 (A2). Press UP
or DOWN; will appear on the screen.
To deactivate the alarm, press UP or DOWN again; the icon will disappear.
The active alarm(s) will then trigger at the set time.
Snooze Function
Alarm ringing can be postponed by 5 minutes using the SNOOZE/LIGHT button located on the top of
the weather station.
Press the button when the alarm starts ringing. The alarm icon and Zz icon will be flashing.
To cancel SNOOZE mode, press any other button except SNOOZE/LIGHT – the icon will stop flashing
and will remain on the screen.
The alarm will be re-activated the next day.
If you do not press any button while the alarm is ringing, the ringing will stop automatically after
2 minutes.
The alarm will trigger again the next day.
Station Screen Illumination
When powered via adapter:
Permanent screen illumination is set automatically.
Repeatedly pressing the SNOOZE/LIGHT button will allow you to set 3 different modes for permanent
illumination (maximum, low, off).
When powered only by 3× 1.5 V AAA batteries:
Screen illumination is off. Pressing the SNOOZE/LIGHT button will turn screen illumination on for
10 seconds,
then it turns off again. When the station is only powered by batteries, permanent screen illumination
cannot be activated!
Note: The inserted batteries serve as backup for the measured/set data. If batteries are not inserted
and you unplug the adapter, all data will be erased.
Содержание E5111
Страница 2: ...2 2 1 5 2 3 6 4 1 1 2 3 4 5 6 7 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 8 9 10 11 12 13 14...
Страница 93: ...93 7 8 9 10 11 12 12 24 15 20 70 100 12 7 12 24 1 2 3 4 5 6 1 2 3 4 1 C 5 1 C 6 1 C...
Страница 94: ...94 C EMOS spol s r o E5111 2014 53 http www emos eu download...
Страница 95: ...95...