background image

Type B/240

Natural Gas Technologies

Emerson Process management

regulator Technologies, Inc.

O.M.T

Officina Meccanica Tartarini s.r.l.

Via P. Fabbri, 1 

I - 40013 Castel Maggiore (Bologna)

Italy  

Tel. : +39 - 0514190611 

Fax: +39 - 0514190715 

E-mail: [email protected]

The Emerson logo is a trademark and service mark of Emerson Electric Co.  All other marks are the property of their prospective owners. Tartarini is a mark of O.M.T. Officina Meccanica Tartarini s.r.l., 

a business of Emerson Process Management.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guaran-

tees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such products at 

any time without notice.

Emerson Process Management does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson Process 

Management product remains solely with the purchaser.

© O.M.T.  Officina Meccanica Tartarini s.r.l., 2010 ; All Rights Reserved

For further information visit: www.emersonprocess.com/regulators

Emerson Process management

Natural Gas Technologies 

Francel SA

Z.A. La Croix Saint Mathieu 

28320 Gallardon

France  

Tel. : +33 (0)2.37.33.47.00 

Fax : +33 (0)2.37.31.46.56 

Содержание Tartarini B/240 Series













Отзывы: