manualshive.com logo in svg

Emerson SolaHD SPD200K Series, Руководство пользователя

Поделиться
Скачать
Emerson SolaHD SPD200K Series Скачать руководство пользователя страница 11

Page: 9

SPD200K/300K

4.  Install in accordance with national and local electrical codes for overcurrent protection recommendations 

and wire ampacity considerations.  
 

Note: Use on solidly grounded systems unless the SPD model is designed for installation on ungrounded 
/HRG systems.  
 
Note: See “Terminals, Wire Size, and Installation Torque” and Table 2 on page 5 for acceptable wire size and 
installation torque.

5.  Twist conductors 1/2 turn or more for every twelve inches of length. Do not loop or coil wires. Be sure to 

maintain adequate wire bending space per NEC.

6.  If the remote signaling contacts of the diagnostic display panel are to be used, refer to the section, “Dry 

Contacts,” on page 14 for wiring instructions.

7.  Replace all devices, doors, and covers before turning on power to the equipment. If the SPD is properly 

installed and functioning, the green LED indicators on the display will be lit and the service LED 
extinguished. 

If you have any questions pertaining to the installation of this device, contact us at 1-800-377-4384  
or [email protected].

Dimensions and Weights

Model

H/W/D (in. / mm.)

Weight

SPD200K / SPD300K

12" x 12" x 6" (305 x 305 x 152)

23 lbs (10.4 kg)

Figure 8:  Typical Panel Installation

When breaker connecting, use 
closest breaker to SPD

Locate SPD close  
to intended breaker

Keep Leads Short as Possible

Avoid Sharp Bends

Outdoor installation requires 
appropriate weather sealing  
at nipple (gasket, sealing  
conduit, etc.)

To Protected Loads

A

B

C

G

N

BREAKER

Содержание SolaHD SPD200K Series





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды