Emerson SMARTSET CKS1708, Руководство по обслуживанию

Страница: 9 / 26

5) Adjust the VOLUME control to the desired seting.
6) When you are finished listening, press the RADIO
ON/OFF button to turn the radio “OFF”
Storing and Recalling Radio
Station Memory
When you have a few favorite radio station to listen to,
you may like to save them, and pick one out of them I
a few seconds without needing to search it each time.
our digital tuning technology allows you to do this
easily by following the following steps.
Storing to the memory
1) Make sure the radio is ON and the AM/FM band is
selected .
2) Tune to the desired station by the TUNING control
as desired.
3) Press STORE, “P XX” blinks, indicating the
memory location to store the currently listening
station.
4) While “P XX” is blinking, press TUNE + or TUNE –
can change the memory location from 1 through 10.
For e.g., “P 03” means the current listening station
is about to stored into the 3
rd
location of the
memory.
5) After deciding the memory location, press STORE
again, the currently listening station is stored.
6) The display will turn to the frequency of the station
afterwards, and after a few seconds, the correct
time shows.
Recalling Station from the memory
1) Make sure the radio is ON and the AM/FM band is
selected.
2) Press MEMORY,
“
P XX” shows on the display,
and the station according to the memory location is
tuned.
3) While “P XX” is showing on the display, press
TUNE + or TUNE – can change the memory
location from 1 through 10, and the station stored
in the location is tuned once the location is
changed to.
4) The display will turn to the frequency of the
stations afterwards, and after a few seconds, the
correct time shows.
Antenna Information
AM – The AM bar antenna is inside the cabinet. If AM
reception is weak, change the position of cabinet until the
internal antenna picks up the strongest signal.
FM – The FM antenna is built in to the Line cord connecting the
AC adapter. If FM reception is weak try varying the position
and direction of the line cord until you find the strongest signal.
Wake To Radio
1) Turn the radio “ON” and selected the band, station, and
volume level that you wish to hear when the alarm comes
“ON”, then turn the radio “OFF
“
again.
2) Reconfirm the wake up time and alarm mode settings for
the alarm you are using, Alarm 1 , Alarm 2 , or both alarms.
3) Press ALARM 1 or ALARM 2 button slightly, and repeat
doing so if necessary, until ALARM 1 RADIO or ALARM 2
RADIO indicator is lit on the display.
4) At the selected wake up time the radio will turn “ON”. It will
play for one hour and then shut off automatically.
5) To stop the radio sooner, press the RADIO ON/OFF button.
The radio will stop but the alarm remains set and will turn
the radio on again at the same time on the following day
(depending in the alarm mode setting).
6) If you do not want the alarm to turn the radio on the radio
on the following day, press the appropriate ALARM button
until the ALARM indicator on the display is OFF.
Note: To avoid your missing wake up time, even if you set the
radio to a very low volume or even silent before turning off the
radio, medium volume will come out of the speaker upon the
alarm time comes.
Wake To Buzzer
NOTE: Alarm 1 and Alarm 2 have different buzzer sounds.

Alarm is a “Signle beep” sound.

Alarm 2 is a “Double beep” sound.
You will be able to tell which alarm is going off by the sound
that it makes.
1) Reconfirm the wake up time and alarm mode settings for
the alarm you are using, Alarm 1, Alarm 2, or both alarms.
2) Press ALARM 1 or ALARM 2 button slightly, and repeat
doing so if necessary, until ALARM 1 “BUZZER” or
ALARM 2 “BUZZER” indicator is lit on the display.
3) At the selected wake up time the buzzer will sound. It will
continue for one hour and then shut off automatically.
4) To stop the buzzer sooner, press the RADIO ON/OFF
button. The buzzer will stop but the alarm remains set and
will turn the buzzer on again at the same time on the
following day (depending on the Alarm Mode setting).