Emerson SMARTSET CKS1708, Руководство по обслуживанию

Страница: 10 / 26

5) If you do not want the alarm to turn the radio on
the following day, press the appropriate ALARM
button until the ALARM indicator on the display is
OFF.
Radio and Buzzer Operation
You may also set one alarm for wake to RADIO and
the other for wake to BUZZER. Just press the ALARM1
and ALARM 2 buttons to the desired status as shown
on the ALARM indicatior.
Snooze / Repeat Alarm
After the alarm turns “ON” in the morning you can
SNOOZE / SLEEP OFF button on the top cabinet for a
few extra minutes sleep. The corresponding ALARM
indicator will flash. The alarm will stop for
approximately 9 minutes and then comes “ON” again.
The Snooze operation may be repeated several times
if desired but after one hour the alarm will not come on
again.
Sleep To Music Timer
You can program the sleep timer to play the radio for
up to 90 minutes and then shut “OFF” automatically.
1) Press the SLEEP button. The display will briefly
show “10” and the radio will begin to play. After 10
minutes countdown the radio will shut off
automatically. Each time you press the SLEEP
button the sleep timer will start at 10 minutes. This
is the sleep timer default setting.
2) To increase or decrease the amount of time that
the radio will play before shutting off, hold the
SLEEP button and press either the SET + or –
button to change the display to the desired sleep
time, up to a maximum of ”90” minutes or a
minimum of “02” minutes.
Note: when you change the sleep timer from the 10
minute default setting to a different setting ,the new
setting becomes the default setting and count down to
zero from the point.
3) To cancel the sleep timer before it counts down to
“00” and shut the radio “OFF” immediately ,press
the SNOOZE/SLEEP OFF bar.
IMPORTANT: Remember that the station and
volume setting you choose for the Sleep To Music
operation are the same settings you will hear if you
set the alarm for Wake To Radio the following
morning.
DIMMER Control
The Dimmer control was set to High position at our
factory. If you find the clock display is too bright in a
darkened room ,set the Dimmer by pressing
SNOOZE/SLEEP OFF/DIMMER button, when radio is
off.
Changing The Lithium Battery
Like all batteries, eventually the built in lithium batter will
need to be replaced. A number of factors, such as, the
length of time between the date the radio was
manufactured and the date you plugged it in for the first
time determine the amount of time before replacement.
During this initial storage period
，
the lithium battery is
supplying power to the Smartset computer memory. Once
you plug the radio in, you household outlet supplier the
power, and the battery is not being used. A fresh lithium
battery can supply power to the Smartset computer for at
least 3 years even if is never connected to an AC power
supply. If your clock radio was connected to your AC
supply within a few months after it was manufactured, and
you experience only the normal, nuisance type, short
duration power interruptions, your battery may last for up to
5 years or even longer.
When the battery power drops below a certain level, the
LOW BATT. Indicator will “Flash”. When you see this
indicator, you should change the battery as soon as it is
convenient for you to do so. To change the battery proceed
as follows:
1) Purchase a replacement 3V lithium battery wherever
batteries are sold. The battery type is CR2032 or
equivalent.
2) Remove the battery from its package so it is ready to
install.
IMPORTANT: Leave the AC adapter connected to your AC
outlet. This will provide power to the Smartset computer
memory while the original lithium battery is removed.
3) Turn the radio face up and used a small screw driver to
remove the screw securing the battery holder to the
cabinet.
BE CAREFULL NOT TO LOSE THIS SMALL SCREW
！
4) Remove the original battery from the holder and insert
the new battery in to the holder the same way,
observing the positive (+) direction. Slide the holder
with the new battery back into the slot in the cabinet.
5) Replace the screw that secures the battery holder in
the cabinet.