Emerson Rosemount Xi Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 82

background image

7

Replacement parts

7.1

Rosemount Xi electronics

Table 7-1: Replacement parts for Rosemount Xi

Part number

Description

6A00265G01

Kit, power supply board (obsolete - replaced by 6A00329G01)

6A00329G01

Kit, switching power supply board

6A00266G01

6A00267G01

Kit, AC relay board

6A00328G01

Kit, DR board

6A00268G01

Kit, front panel with overlay and CPU board

6A00268G02

Kit, front panel with overlay

6A00269G01

Enhanced software option upgrade, Stoichiometric function

6A00269G02

Enhanced software option upgrade, programmable reference function

6A00269G03

Enhanced software option upgrade, 800 °C process function

6A00237H24

Kit, pipe and wall mount

6A00237H33

Kit, panel mount

6A00243G01

Ribbon cable, 10 pin (CPU board to I/O board)

6A00242G01

Ribbon cable, 14 pin (CPU board to power supply board)

6A00291H01

Insulator

6A00381G01

Kit, hole plug and gland

6A00285H01

Gasket, panel

6A00287H01

Gasket, cover

(1)

If the existing I/O board has been operated with the Stoichiometric enhanced software feature,
this feature must be activated in the new board before the Rosemount Xi is put back into service.
Failure to do so will cause a false analog output signal to the DCS.

Reference Manual

Replacement parts

00809-0100-4889

October 2022

Emerson.com/Rosemount

75

«
...
73
74
75
76
77
...
»

Содержание Rosemount Xi



















































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Xi

Stage Piano MP8

Бренд: Kawai Страницы: 70

Бренд: LaMotte Страницы: 2

Бренд: Lampa Страницы: 12

Vario 4 Typ 4.5.1

Бренд: techem Страницы: 142

Бренд: Dynojet Страницы: 88

Бренд: VP instruments Страницы: 15

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

Бренд: Tektronix Страницы: 20

Бренд: Ratek Страницы: 24

Бренд: Oldham Страницы: 106

Бренд: Bruker BioSpin Страницы: 76

sound SMART RLT Sport

Бренд: VCA Страницы: 36

Бренд: Agilent Technologies Страницы: 26

AERASGARD FSFTM-CO2-Modbus Series

Бренд: S+S Regeltechnik Страницы: 32

Бренд: AL Страницы: 2

Бренд: HEIDENHAIN Страницы: 28

Бренд: ATIM Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды