Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя

Страница: 8 / 60

Reference Manual

00809-0100-4075, Rev BA

October 2010

Smart Wireless THUM Adapter

1-2

OVERVIEW

Manual

This manual is designed to assist in the installation, operation, and
maintenance of the Smart Wireless THUM™ Adapter.

Section 1: Introduction

•

Manual and Transmitter Overview

•

Considerations

•

Return of Materials

Section 2: Configuration

•

Device Sensor Configuration

•

Device Network Configuration

Section 3: Mounting

•

Mount the Sensor

•

Sensor Assembly/Leads

•

Grounding

Section 4: Commissioning

•

Network Status

•

Verify Operation

Section 5: Operation and Maintenance

•

Startup Sequence

•

Advanced Setup

Appendix A: Reference Data

•

Specifications

•

Dimensional Drawings

•

Ordering Information

Appendix B: Product Certifications

•

Product Certifications

•

Installation Drawings

Features

•

An installation-ready solution that provides rich wireless HART

data

•

Works with any 2- or 4-wire HART devices

•

Flexibility to meet your most demanding applications

•

Wireless output with >99% data reliability delivers rich HART data,
protected by industry leading security

•

Gain access to additional HART information, such as diagnostics or
multi-variable data

•

Add wireless to almost any measurement point without affecting the
approval of the sub-device

•

IEC 62591 (WirelessHART™) capabilities extend the full benefits of
PlantWeb

to previously inaccessible locations

Содержание Rosemount Smart Wireless THUM





























































Результаты поиска

Содержание Rosemount Smart Wireless THUM

Отзывы:

Похожие инструкции для Rosemount Smart Wireless THUM

Бренды по названию

Популярные бренды

Emerson Rosemount Smart Wireless THUM, Справочное руководство

Результаты поиска

Содержание Rosemount Smart Wireless THUM

Отзывы:

Похожие инструкции для Rosemount Smart Wireless THUM

Бренды по названию

Популярные бренды