manualshive.com logo in svg

Emerson Rosemount Smart Wireless THUM, Справочное руководство

Emerson Rosemount Smart Wireless THUM является передовым устройством для измерения температуры и влажности. Для получения подробной информации о продукте, загрузите бесплатное Руководство по эксплуатации с нашего веб-сайта. Узнайте больше о его функциональности и возможностях, загрузив руководство с manualshive.com.

Поделиться
Скачать
background image

Reference Manual 

00809-0100-4075, Rev BA
October 2010

B-1

Smart Wireless THUM Adapter

Appendix B

Product Certifications

Approved Manufacturing Locations  . . . . . . . . . . . . . . . . . page B-1
European Directive Information   . . . . . . . . . . . . . . . . . . . . page B-1
Telecommunication Compliance  . . . . . . . . . . . . . . . . . . . . page B-1
FCC and IC   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page B-1
Ordinary Location Certification for FM . . . . . . . . . . . . . . . page B-1
Hazardous Locations Certificates . . . . . . . . . . . . . . . . . . . page B-1

Approved Manufacturing 
Locations

Rosemount Inc. – Chanhassen, Minnesota, USA

Emerson Process Management GmbH & Co. - Karlstein, Germany

Emerson Process Management Asia Pacific Private Limited - Singapore

European Directive 
Information

The EC declaration of conformity for all applicable European directives for this product can be 
found at www.rosemount.com. A hard copy may be obtained by contacting an Emerson Process 
Management representative.

ATEX Directive (94/9/EC)

Emerson Process Management complies with the ATEX Directive.

Electro Magnetic Compatibility (EMC) (2004/108/EC

)

Emerson Process Management complies with the EMC Directive.

Radio and Telecommunications Terminal Equipment Directive (R&TTE) (1999/5/EC)

Emerson Process Management complies with the R&TTE Directive.

Telecommunication 
Compliance

All wireless devices require certification to ensure that they adhere to regulations regarding the 
use of the RF spectrum. Nearly every country requires this type of product certification. Emerson 
is working with governmental agencies around the world to supply fully compliant products and 
remove the risk of violating country directives or laws governing wireless device usage.

FCC and IC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
conditions: This device may not cause harmful interference. This device must accept any 
interference received, including interference that may cause undesired operation.This device 
must be installed to ensure a minimum antenna separation distance of 20 cm from all persons.

Ordinary Location 
Certification for FM

As standard, the transmitter has been examined and tested to determine that the design meets 
basic electrical, mechanical, and fire protection requirements by FM, a nationally recognized 
testing laboratory (NRTL) as accredited by the Federal Occupational Safety and Health 
Administration (OSHA).

Hazardous Locations 
Certificates

North American Certifications

Factory Mutual (FM) Approvals

I5

FM Intrinsically Safe and Non-incendive
Intrinsically Safe for Class I/II/III, Division 1, Groups A, B, C, D, E, F, and 
G.
Zone Marking: Class I, Zone 0, AEx ia llC
Temperature Codes T4 (-50 °C 



T

amb 



70 °C)

Non-incendive for Class I, Division 2, Groups A, B, C, and D. 
Intrinsically safe and non-incendive when installed according to 
Rosemount Drawing 00775-0010.
Enclosure Type 4X/IP66

Содержание Rosemount Smart Wireless THUM





























































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Smart Wireless THUM

Mobeli QuattroPlus 1400557 Instruction Manual preview
QuattroPlus 1400557
Бренд: Mobeli Страницы: 4
Parabel CR-505 User Manual preview
CR-505
Бренд: Parabel Страницы: 16
Linksys AG310 User Manual preview
AG310
Бренд: Linksys Страницы: 87
IBM ThinkPad Enhanced Drive Adapter User Manual preview
ThinkPad Enhanced Drive Adapter
Бренд: IBM Страницы: 82
Pullman Holt 102-DA Operation & Care Instructions Manual preview
102-DA
Бренд: Pullman Holt Страницы: 6
CICH International EzCast M2 Manual preview
EzCast M2
Бренд: CICH International Страницы: 7
VOLTCRAFT 2258704 Operating Instructions preview
2258704
Бренд: VOLTCRAFT Страницы: 4
Air Live SKY-211 Quick Setup Manual preview
SKY-211
Бренд: Air Live Страницы: 50
Tripp Lite Thunderbolt MTB3-002-HD Quick Start Manual preview
Thunderbolt MTB3-002-HD
Бренд: Tripp Lite Страницы: 31
Greenlee CMAF-1000 Instruction Manual preview
CMAF-1000
Бренд: Greenlee Страницы: 36
Avaya M12LU User Manual preview
M12LU
Бренд: Avaya Страницы: 2
IOGear GUC232A Quick Start Manual preview
GUC232A
Бренд: IOGear Страницы: 10
Digitus DN-30210 User Manual preview
DN-30210
Бренд: Digitus Страницы: 30
Alogic DCAP-SPL Quick Start Manual preview
DCAP-SPL
Бренд: Alogic Страницы: 2
Belkin F5U120-PC User Manual preview
F5U120-PC
Бренд: Belkin Страницы: 124
Compex WAVEPORT WL11 Quick Install Manual preview
WAVEPORT WL11
Бренд: Compex Страницы: 57
CoolAutomation CoolPlug Programmer'S Manual preview
CoolPlug
Бренд: CoolAutomation Страницы: 6
Uconnect BLE-485C User Manual preview
BLE-485C
Бренд: Uconnect Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды