Emerson Rosemount Smart Wireless THUM Скачать руководство пользователя | Manualshive

Страница: 45 / 60

background image

Reference Manual

00809-0100-4075, Rev BA
October 2010

A-1

Smart Wireless THUM Adapter

Appendix A

Reference Data

Functional Specifications   . . . . . . . . . . . . . . . . . . . . . . . . . page A-1
Physical Specifications   . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-1
Performance Specifications   . . . . . . . . . . . . . . . . . . . . . . . page A-2
Dimensional Drawings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-3
Ordering Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-5

FUNCTIONAL
SPECIFICATIONS

Input

Any 2- or 4-wire HART powered device.

Output

IEC 62591 (WirelessHART)

Humidity Limits

0–100% relative humidity

Update Rate

User selectable, 8 sec. to 60 min.

PHYSICAL
SPECIFICATIONS

Electrical Connections

The THUM is connected into a powered 4–20 mA loop, powering itself by
scavenging power. The THUM causes a voltage drop across the loop. The
drop is linear from 2.25 volts at 3.5 mA to 1.2 volts at 25 mA, but does not
effect the 4–20 mA signal on the loop. Under fault conditions, the maximum
voltage drop is 2.5 volts.

Power Supply

Minimum load on loop 250 Ohms.

To maintain normal operating functions of the sub-device, the power in the
loop must have at least a 2.5 V margin at a 250 Ohm load.

Limit power supply to 0.5 Amps maximum.

Limit power supply to 55 Vdc maximum.

Field Communicator Connections

Utilize sub-device HART connections.

Materials of Construction

Housing option D - Low-copper aluminum

Housing option E - 316 SST

Paint - Polyurethane

M20-Conduit Adapter - SST

M20-Conduit Adapter O-ring - Buna-n

Antenna

Poly butadine terephthalate (PBT) / Polycarbonate (PC) integrated
omnidirectional antenna

«
...
43
44
45
46
47
...
»

Содержание Rosemount Smart Wireless THUM





























































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount Smart Wireless THUM

Бренд: quadient Страницы: 2

Бренд: powerpack Страницы: 9

Бренд: Mercusys Страницы: 59

Бренд: comPPage Страницы: 38

Bluetooth USB-Adapter Version 1.2

Бренд: Hama Страницы: 8

Бренд: H3C Страницы: 13

Бренд: Powerlink Страницы: 28

Бренд: NETGEAR Страницы: 2

ALMEMO 8006-RTA3

Бренд: Ahlborn Страницы: 16

Бренд: 3idee Страницы: 6

Бренд: CAB Страницы: 10

FM 5 IN DASH ADAPTER KIT

Бренд: Eagle Страницы: 5

Бренд: SP Controls Страницы: 2

Бренд: NETGEAR Страницы: 12

Бренд: NETGEAR Страницы: 16

Бренд: Arduino Страницы: 10

Бренд: QuantumZERO Страницы: 3

Бренд: Paradyne Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды