Emerson Rosemount 8732E Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 38

background image

Quick Installation Guide

00825-0100-4662, Rev CC

December 2012

Rosemount 8732

2

© 2013 Rosemount Inc. All rights reserved. All marks property of owner.

IMPORTANT NOTICE

This document provides basic installation guidelines for the Rosemount

®

8732. It does

not provide instructions for detailed configuration, diagnostics, maintenance, service,
troubleshooting, explosion-proof, flame-proof, or intrinsically safe (I.S.) installations.
Refer to the Rosemount 8732 reference manual (document number 00809-0100-4662)
for more instructions. The manual and this QIG are also available electronically on
www.rosemount.com.

WARNING

Failure to follow these installation guidelines could result in death or serious
injury:

Installation and servicing instructions are for use by qualified personnel only. Do not
perform any servicing other than that contained in the operating instructions, unless
qualified. Verify that the operating environment of the sensor and transmitter is consistent
with the appropriate FM, CSA, ATEX, or IECEx approval.

Do not connect a Rosemount 8732 to a non-Rosemount sensor that is located in an
explosive atmosphere.

WARNING

The sensor liner is vulnerable to handling damage. Never place anything through the
sensor for the purpose of lifting or gaining leverage. Liner damage can render the sensor
useless.

To avoid possible damage to the sensor liner ends, do not use metallic or spiral-wound
gaskets. If frequent removal is anticipated, take precautions to protect the liner ends.
Short spool pieces attached to the sensor ends are often used for protection.

Correct flange bolt tightening is crucial for proper sensor operation and life. All bolts must
be tightened in the proper sequence to the specified torque limits. Failure to observe
these instructions could result in severe damage to the sensor lining and possible sensor
replacement.

WARNING

Rosemount 8705 Magnetic Flowtube units ordered with non-standard paint options may
be subject to electrostatic discharge.

To avoid electrostatic charge build-up, do not rub the meter body with a dry cloth or clean
with solvents.

Emerson Process Management
Rosemount Flow

7070 Winchester Circle,
Boulder, CO 80301
Tel (USA) 800 522 6277
Tel (International) +1 (303) 527 5200
Fax +1 (303) 530 8459

Emerson Process
Management Flow

Neonstraat 1
6718 WX Ede
The Netherlands
T +31 (0)318 495555
F +31(0) 318 495556

Emerson Process
Management Asia Pacific
Private Limited

1 Pandan Crescent
Singapore 128461
T (65) 6777 8211
F (65) 6777 0947/65 6777 0743

Emerson FZE

P.O. Box 17033
Jebel Ali Free Zone
Dubai UAE
Tel +971 4 811 8100
Fax +971 4 886 5465

4662RevCCQIG.fm Page 2 Thursday, January 10, 2013 5:11 PM

«
1
2
3
4
...
»

Содержание Rosemount 8732E







































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 8732E

Бренд: Varec Страницы: 24

THERMASGARD TM 65

Бренд: S+S Regeltechnik Страницы: 16

PREMASGARD 211 Series

Бренд: S+S Regeltechnik Страницы: 11

Dpharp vigilantplant EJA Series

Бренд: YOKOGAWA Страницы: 31

Бренд: Yaesu Страницы: 35

Бренд: DAPAudio Страницы: 20

Smart Tag ST008

Бренд: SportIQ Страницы: 3

Бренд: Gear4 Страницы: 104

Бренд: IROX Страницы: 2

FM Transmitter 2

Бренд: C. Crane Страницы: 13

Бренд: Icom Страницы: 32

Бренд: Patton electronics Страницы: 4

Бренд: Icom Страницы: 40

Бренд: Ham radio Страницы: 14

Бренд: M-system Страницы: 2

Бренд: AFi Страницы: 8

Бренд: Smith Meter Страницы: 8

Бренд: Icom Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды