Emerson Rosemount 752 FOUNDATION Скачать руководство пользователя

Страница: 34 / 48

Reference Manual

00809-0100-4377, Rev CA

Troubleshooting

January 2018

Troubleshooting

Table 4-1. Troubleshooting guide.

Symptom

(1)

The corrective actions should be done with consultation of your system integrator.

Cause

Recommended Actions

Device does not show up on

segment

Unknown

Recycle power to device

No power to device

1. Ensure the device is connected to the segment.

2. Check voltage at terminals. There should be 9–32

Vdc.

3. Check to ensure the device is drawing current. There

should be approximately 17 mA.

Segment problems

Electronics failing

1. Electronics board loose in housing.

2. Replace electronics.

Incompatible network settings

Change host network parameters.

Refer to host documentation for procedure.

Device does not stay on

segment

(2)

Wiring and installation 31.25 kbit/s, voltage mode, wire medium application guide AG-140 available from the fieldbus Foundation.

Incorrect signal levels.

Refer to host documentation for

procedure.

1. Check for two terminators.

2. Excess cable length.

3. Bad Power supply or conditioner

Excess noise on segment.

Refer to host documentation for

procedure.

1. Check for incorrect grounding.

2. Check for correct shielded wire.

3. Tighten wire connections.

4. Check for corrosion or moisture on terminals.

5. Check for Bad power supply.

Electronics failing

1. Tighten electronics board.

2. Replace electronics.

Other

1. Check for water in the terminal housing.

Содержание Rosemount 752 FOUNDATION

















































Результаты поиска

Содержание Rosemount 752 FOUNDATION

Отзывы:

Похожие инструкции для Rosemount 752 FOUNDATION

Бренды по названию

Популярные бренды

Emerson Rosemount 752 FOUNDATION, Справочное руководство

Результаты поиска

Содержание Rosemount 752 FOUNDATION

Отзывы:

Похожие инструкции для Rosemount 752 FOUNDATION

Бренды по названию

Популярные бренды