manualshive.com logo in svg

Emerson Rosemount 3051S Series, Быстрое руководство по установке

Поделиться
Скачать
Emerson Rosemount 3051S Series Скачать руководство пользователя страница 3

Quick Installation Guide

00825-0100-4801, Rev HA
February 2008

Rosemount 3051S

3

WARNING

Explosions could result in death or serious injury:

 

Installation of this transmitter in an explosive environment must be in 
accordance with the appropriate local, national, and international 
standards, codes, and practices. Please review the approvals section of 
the 3051S reference manual for any restrictions associated with a safe 
installation. 

• Before connecting a HART communicator in an explosive 

atmosphere, ensure the instruments in the loop are installed in 
accordance with intrinsically safe or non-incendive field wiring 
practices.

• In an Explosion-Proof/Flame-Proof installation, do not remove the 

transmitter covers when power is applied to the unit. 

Process leaks may cause harm or result in death.

 

• Install and tighten process connectors before applying pressure.

Electrical shock can result in death or serious injury.

• Avoid contact with the leads and terminals. High voltage that may be 

present on leads can cause electrical shock.

4801_QIG_RevHA.fm  Page 3  Tuesday, February 26, 2008  12:17 PM

Содержание Rosemount 3051S Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды