Emerson Net Safety SC311 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

background image

Installation

Reference Manual

June 2016

MAN-0091, Revision 8

6

Installation

Figure 2-4 SC311 Sensor mounted to Millennium II series transmitters

2.6

Wiring

2.6.1

Field installation

Failure to follow these installation guidelines could result in death or serious injury. Ensure that only
qualified personnel perform the installation.

Electrical shock could cause death or serious injury. Use extreme caution when making contact with
the leads and terminals.

Do not open the transmitter, sensor, or junction box enclosure when in a classified area or when an
explosive atmosphere may be present unless the power to the transmitter and sensor has been
removed.

Wiring codes and regulations may vary. Wiring must comply with all applicable regulations relating to
the installation of electrical equipment in a hazardous area and is the responsibility of the installer. If in
doubt, consult a qualified official before wiring the system.

When separating the sensor from the transmitter, the use of shielded cable is highly recommended to
protect against interference caused by extraneous electrical or electromagnetic noise. In applications
where the wiring is installed in conduit, the conduit must not be used for wiring to other equipment.

Millennium II Basic Transmitter &

Junction Box

Millennium II Transmitter

3/4” NPT

Locking
collar

Sensor
pointing
downwards

SC311 Sensor mouth
and sintered element

3/4” NPT

SC311 Sensor mouth
and sintered element

Locking
collar

Sensor
pointing
downwards

3/4” NPT

3/4” NPT

«
...
11
12
13
14
15
...
»

Содержание Net Safety SC311





































Отзывы:

Нет отзывов

Похожие инструкции для Net Safety SC311

Бренд: UnderCover Страницы: 16

Бренд: Safco Страницы: 6

Бренд: Karma Страницы: 7

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Napoleon Страницы: 2

Бренд: Parker Страницы: 2

Бренд: Park Tool Страницы: 2

Бренд: ParaZero Страницы: 17

Бренд: M-Audio Страницы: 14

MADLOCKER MLP-1

Бренд: MADRAX Страницы: 6

Бренд: BGS technic Страницы: 5

Бренд: PCB Piezotronics Страницы: 7

Baby Go Round Twirl

Бренд: Redkite Страницы: 4

FT2A-PWR-IT Series

Бренд: Crestron Страницы: 2

Бренд: Asong Страницы: 17

Бренд: A&D Страницы: 10

Бренд: Boxee Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды