Emerson Liebert APM 120 Скачать руководство пользователя страница 97

Страница: 97 / 144

Operator Control and Display Panel

Liebert

APM

™

9.3

Control Buttons

The

Control Buttons

on the front panel may be used to shut down the UPS completely, turn the

inverter on or off, restart the UPS after a fault and silence the alarm, as shown in

Figure 70

. The

function of each button is described in

Table 24

Figure 70 Control button layout

9.4

Alarm Buzzer

The alarm buzzer produces three types of sounds:

•

Single beep

—When any Control button is pressed

•

Single beep repeating every two seconds

—The system has a general alarm

•

Continuous

—The system has a serious fault

If the alarm buzzer makes no sound, the system may be operating properly or the alarm may have

been silenced manually.

Figure 71 Alarm buzzer location

NOTE

To activate a button properly, press and hold until you hear a short beep—about two seconds.

Table 24

Control buttons

Button

(see Figure 70)

Function

EPO

Completely shuts down the UPS, including the static switch.

CAUTION:

Use caution before pressing the Emergency Power Off (EPO) button. This button

completely shuts down the unit and the critical load.

INVERTER ON

Press this button to start the inverter and transfer from static bypass to inverter.

NOTE:

If the inverter is not ready, this will not activate the UPS.

INVERTER OFF

Press this button to shut down the inverter during operation. The load will be transferred to

static bypass.

FAULT CLEAR

After the UPS shuts down due to a fault and the alarm condition has been resolved, press this

button to clear the fault and restart the UPS.

SILENCE ON/OFF

Press this button once to silence the alarm buzzer when an alarm is active. Any new fault will

sound the buzzer again.

If the alarm buzzer is not beeping, press this button to test the alarm sound.

STATUS

EMER SO N

Network Power

HELP

FAULT CLE AR

E P O

INV E RTE R OFF

S ILE NCE ON/ OFF

INV E RTE R ON

EPO Button Cover

EPO Button

Inverter Off Button

Fault Clear Button

Silence On/Off Button

Inverter On Button

LCD Navigation Keys

STATUS

EME R SO N

Network Power

HELP

FAULT CLE AR

E P O

INV E RTE R OFF

S ILE NCE ON/ OFF

INV E RTE R ON

Buzzer

Содержание Liebert APM 120

















































































































































Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды

Emerson Liebert APM 120, Руководство пользователя

Результаты поиска

Содержание Liebert APM 120

Отзывы:

Похожие инструкции для Liebert APM 120

Бренды по названию

Популярные бренды