background image

www.Fisher.com

Fisher

 V280 Full-Bore Ball Control Valve

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Educational Services

3

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

5

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Packing Maintenance

6

. . . . . . . . . . . . . . . . . . . . . . . . .

Stopping Leakage

6

. . . . . . . . . . . . . . . . . . . . . . . .

Replacing Packing

6

. . . . . . . . . . . . . . . . . . . . . . . .

Seal Ring Maintenance

9

. . . . . . . . . . . . . . . . . . . . . . .

Disassembly

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assembly

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Actuator Mounting

13

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Determining Closed Position

13

. . . . . . . . . . . . . . . . .

Parts Ordering

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher V280 Control Valve

X1611

Introduction

Scope of Manual

This instruction manual provides installation, operation, maintenance, and parts information for the Fisher V280
Full-Bore Ball control valve (see figure 1). Refer to separate manuals for information concerning the actuator,
positioner, and accessories.

Do not install, operate, or maintain a V280 valve without being fully trained and qualified in valve, actuator, and
accessory installation, operation, and maintenance. 

To avoid personal injury or property damage, it is important to

carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings.

 If you

have any questions about these instructions, contact your 

Emerson sales office

 before proceeding.

Description

The Fisher V280 is a three-piece, trunnion mounted, full-bore control valve designed with features for optimized
pressure, flow, and process control. The V280 comes standard as a single-seal construction with optional dual-seal
construction allowing for bidirectional flow and double block-and-bleed operation, with or without attenuation. Valve
constructions with attenuators combine the efficiency of a rotary valve with the noise reducing capability of a special
trim. Valve constructions without attenuators present little or no restriction to flow at full travel. The V280
construction meets ANSI/NACE MR0175/ISO 15156 as standard.

Instruction Manual

D104425X012

V280 Valve

August 2019

Содержание Fisher V280

















Отзывы: