background image

Instruction Manual

D104734X012

ATST Desuperheater

July 2022

8

Parts Ordering

Each ATST desuperheater is assigned a serial number. Refer to the serial number when contacting your 

Emerson sales

office

 for technical assistance. When ordering replacement parts, refer to the serial number and key numbers for each

part required. The key numbers in the Parts List and the assembly drawing in figure 5 can be used to help in part
identification.

  WARNING

Use only genuine Fisher replacement parts. Components that are not supplied by Emerson should not, under any
circumstances, be used in any Fisher desuperheater, because they may void your warranty, might adversely affect the
performance of the desuperheater, and could cause personal injury and property damage.

Parts List

Note

Contact your 

Emerson sales office

 for Part Ordering information.

Key

Description

1

Steam Pipe

2

Nozzle Body

3

Nozzle Alignment Pin

4

Nozzle Body Flange Washer

5

Nozzle Body Flange Stud

6

Nozzle Body Flange Stud Nut

7

Nozzle Body Flange Assembly

Key

Description

8*

Nozzle Body Flange Gasket

9*

Nozzle Gasket

10*

Spray Nozzle

11

 Steam Pipe Liner Guide Ring

12

Steam Pipe Liner

13

Steam Pipe Liner Retention Pin

14

Nameplate (not shown)

*Recommended spare parts

Содержание Fisher ATST Desuperheater













Отзывы: