manualshive.com logo in svg

Emerson Fisher 627B Series, Инструкция по эксплуатации, Страница: 9 / 12

Поделиться
Скачать
Emerson Fisher 627B Series Скачать руководство пользователя страница 9

Parts Ordering

When corresponding with your local Sales Office about this 

equipment, always reference the equipment serial number or 

FS number that can be found on the nameplate.
When ordering replacement parts, reference the key number of 

each needed part as found in the following parts list. Separate 

kits containing all recommended spare parts are available.

Parts List

Note

In this parts list, parts marked NACE are 

intended for corrosion-resistant service 

as detailed in the NACE International 

Standard MR0175.

Key  Description 

Part Number

1  

Body

(1)

 

Ductile iron 

1000 psig / 69.0 bar maximum inlet pressure 

1 NPT   

30B3048X012 

2 NPT   

30B3096X012  

Steel 

2000 psig / 138 bar maximum inlet pressure  

1 NPT   

30B3051X012 

2 NPT   

30B7452X012

Steel, CL600 RF flanged

1500 psig / 103 bar maximum inlet pressure 

NPS 1 / DN 25   

40B6754X012 

NPS 2 / DN 50   

40B6756X012

Steel, CL300 RF flanged

750 psig / 51.7 bar maximum inlet pressure

NPS 1 / DN 25   

41B8978X012 

NPS 2 / DN 50   

41B8080X012

Steel, CL150 RF flanged

290 psig / 20.0 bar maximum inlet pressure

NPS 1 / DN 25   

43B8656X022 

NPS 2 / DN 50   

44B0666X012

Steel, BWE

1000 psig / 69.0 bar maximum inlet pressure

NPS 1 / DN 25   

33B6723X012 

NPS 2 / DN 50   

38B1688X012

Steel, PN 16/25/40 RF

580 psig / 40.0 bar maximum inlet pressure

NPS 1 / DN 25   

44B0386X012 

NPS 2 / DN 50   

44B3342X012

2* Orifice

9/16 in. / 14.3 mm 

Aluminum 1C4252X0012

303 SST   

1C425235032 

316 SST 

1C4252X0022

3 

Cap Screw (not shown), (2 required)

Steel 1A560724052

Stainless steel 

1A5607X0052

5 

Diaphragm Case

For Types 627BM, 627BMR, 627BHM

Ductile iron (not for Type 627BHM) 

ERAA50626A0

Steel ERAA50625A0

8 

Stem Guide

Stainless steel 

ERAA51322A0

9* 

Disk Assembly

316 Stainless steel holder and Nitrile (NBR) disk  ERAA49120A0

316 Stainless steel holder and Nylon (PA) disk  

ERAA49120A1

10 

Stem, 316 Stainless steel (NACE) 

ERAA51314A0

14 

Drive Pin, Stainless steel  

ERAA49515A0

15 

Lever, Carbon steel  

20B3063X012

16 

Lever Retainer, Plated steel  

30B3097X012

17 

Lever Pin

Stainless steel  

10B3083X012

316 Stainless steel (NACE)  

10B3083X022

18 

Lever Cap Screw (2 required)

Plated steel  

10B7454X012

316 Stainless steel (NACE)  

1B2905X0012

*Recommended spare part.

1. Bodies can be used for both standard and NACE constructions.

14.  To remove the diaphragm (key 23), remove the diaphragm 

connector nut (key 22) and lift off the diaphragm head 

(key 24) and diaphragm (key 23) from the connector 

assembly (key 21). Do not attempt to disassemble the 

connector assembly (key 21).

15.  Position the replacement diaphragm (key 23) on the 

connector assembly (key 21), install the diaphragm head 

(key 24) and connector nut (key 22), then torque to torque 

values shown in Table 4.

16.  If necessary, replace the guide retainer O-ring (key 48) and, 

set the guide retainer (key 26) aside, ready for assembly.

17.  On the pusher post (key 19) install the relief seal O-ring 

(key 28) and apply lubricant. Also, install the relief seal 

retainer (key 47), diaphragm connector assembly (key 21, 

with attached parts) relief spring (key 27), upper relief 

spring seat (key 33) and guide retainer (key 26). Torque the 

guide retainer (key 26) to torque values shown in Table 4.

18.  Hook the pusher post (key 19) (with attached parts) on 

the lever (key 15) to check the alignment of the holes in 

the diaphragm with the holes in the spring casing. If the 

holes do not line up, unhook the pusher post from the 

lever, hold the pusher post and rotate the diaphragm to the 

correct position.

19.  Install the lower spring seat (key 31) over the relief spring 

so it rests flat on the connector nut (key 22).

20.  Insert the diaphragm assembly into the diaphragm casing 

(key 5) and hook the pusher post on the lever (key 15).

21.  Install the control spring (key 32) and upper spring 

seat (key 33) and apply lubricant to the upper 

spring seat (key 33).

22.  Install the spring case (key 29) so that the screened 

vent assembly (key 30) is in the correct position for 

the application. Place the nameplates over the screw 

holes, insert the spring case cap screws (key 37) and 

finger tighten.

23.  Screw in the adjusting screw (key 35) to put slack into the 

diaphragm (key 23).

24.  Using a crisscross pattern, finish tightening the spring case 

cap screws (key 37) to torque values shown in Table 4.

25.  If necessary, refer to the installation and/or the Startup and 

Adjustment procedures.

26.  Install the adjusting locknut (key 34) after 

regulator adjustment.

9

627B Series

Содержание Fisher 627B Series













Отзывы:

Нет отзывов