Emerson Fisher 4210 Скачать руководство пользователя страница 11

Страница: 11 / 44

4200 Series Transmitters

Instruction Manual

Form 5596
November 2006

NOTES:

TYPE 4212 AND 4222 POSITION SWITCHES WITHOUT THE TRANSMITTER CIRCUIT DO NOT REQUIRE A RECEIVING DEVICE OR

THE ASSOCIATED WIRING.

RECEIVING DEVICE MAY BE ANALOG CURRENT INPUT TO DISTRIBUTED CONTROL SYSTEM, PROGRAMMABLE LOGIC

CONTROLLER OR INDICATING DEVICE. INDICATING DEVICE CAN BE A VOLTMETER ACROSS A 250 OHM RESISTOR OR A CURRENT
METER.

DURING NORMAL CONDITIONS, RELAYS K1 AND K2 ARE ENERGIZED, WHICH CONNECTS THE COMMON (C) TERMINAL TO THE

NORMALLY OPEN (NO) TERMINAL. A TRIPPED (OR ALARM) CONDITION IS WITH THE RELAY(S) DE-ENERGIZED, WHICH CONNECTS
THE COMMON (C) TERMINAL TO THE NORMALLY CLOSED (NC) TERMINAL.

SEPARATE RETURN REQUIRED FOR RELAYS. RETURN WIRE MUST BE CONNECTED EVEN IF RELAY OUTPUTS ARE NOT USED.

POWER

SUPPLY

−

DEVICE

RECEIVING

4 TO 20 MA

DC SIGNAL

−

DEVICE

RECEIVING LO

POSITION

SWITCH OUT-

PUT (CONTACT

CLOSURE)

DEVICE

RECEIVING HI

POSITION

SWITCH OUT-

PUT (CONTACT

CLOSURE)

TRANSMITTER
FIELD WIRING

FOR TYPE 4210, 4215, OR 4220 TRANSMITTER WITH POSITION SWITCHES AND

FOR TYPE 4212 OR 4222 POSITION SWITCHES WITHOUT THE TRANSMITTER

RELAY RETURN

POWER

SUPPLY

DEVICE

RECEIVING

4 TO 20 MA

DC SIGNAL

−

TRANSMITTER
FIELD WIRING

FOR TYPE 4211 OR 4221 TRANSMITTER WITHOUT POSITION SWITCHES

C0601-4/IL

FIELD CIRCUIT PRINTED
WIRING BOARD

FIELD WIRING
COMPARTMENT

POSITION SWITCH
FIELD WIRING

GROUNDING
TERMINAL
UNDER PRINTED
WIRING BOARD

TB1

TB3

TB2

EARTH
GROUND

GROUNDING
TERMINAL

BARRIER STRIP
(KEY 11)

FIELD WIRING
COMPARTMENT

SAFETY GROUND

Figure 4. Wiring Connections

Содержание Fisher 4210













































Результаты поиска

Содержание Fisher 4210

Отзывы:

Похожие инструкции для Fisher 4210

Бренды по названию

Популярные бренды

Emerson Fisher 4210, Инструкция по эксплуатации

Результаты поиска

Содержание Fisher 4210

Отзывы:

Похожие инструкции для Fisher 4210

Бренды по названию

Популярные бренды