Emerson Fisher 3582 Скачать руководство пользователя страница 43

Страница: 43 / 56

Instruction Manual

D200138X012

3582, 582i, and 3583

January 2013

Figure 22. Nozzle Sub‐Assembly

12A7441‐C

Key

Description

Part Number

Flapper Assembly Retainer, SST

Self Tapping Screw, pl steel (2 req'd)

Nameplate, aluminum

Self Tapping Screw, steel (2 req'd)

Extension Spring, SST

Machine Screw, pl steel (3 req'd)

Beam Sub‐Assembly
For all except 3582NS and high vibration

19B3119X012

For 3582NS and high vibration

22B3645X022

Bellows Pivot Pin, SST

83L Relay (figure 23)
See Parts Kits, Replacement Kit for 83L Relay

Cover Assembly
Plastic
For all types except 3582NS
Aluminum
For all types except 3583, 3583C
For 3583 and 3583C

Note

Bypass block assembly (key 34) and parts are listed later in this parts list.
Non‐bypass block assembly (also key 34) and parts are listed following
the bypass block assembly and parts.

Parts 35, 36 and 37 are shown in figures 24 and 25.

Pipe Plug, pl steel
Req'd when gauges or test connections are not used:
3 req'd for 3582 positioners
Plated carbon steel
316 SST

36* Output Gauge, Dual Scale

3582, 3582G, 3583
0-30 psig/0-2 kg/cm

11B4040X042

0-60 psig/0-4 kg/cm

11B4040X052

Figure 23. 83L Relay

UNITS STAMPED WITH AN H
INDICATE HIGH TEMPERATURE
CONSTRUCTION

32B0255‐B

Key

Description

Part Number

36* Output Gauge, Triple Scale

3582, 3582G, 3583
0-30 psig/0-0.2 MPa/0-2 bar

11B4040X012

0-60 psig/0-0.4 MPa/0-4 bar

11B4040X022

37* Supply Gauge, Dual Scale

3582, 3582G, 3583
0-30 psig/0-2 kg/cm

11B4040X042

0-60 psig/0-4 kg/cm

11B4040X052

37* Supply Gauge, Triple Scale

3582, 3582G, 3583
0-30 psig/0-0.2 MPa/0-2 bar

11B4040X012

0-60 psig/0-0.4 MPa/0-4 bar

11B4040X022

Extension Spring, SST

Shipping Stop (not shown)

Hex Nut, pl steel (2 req'd)

Spring Retainer Bracket, SST

Gear Mounting Plate, aluminum

Locking Nut, aluminum

Note

Parts 46 and 47 are shown in figures 24 and 25.

46* Instrument Gauge, Dual Scale

0-30 psig/0-2 kg/cm

(3-15 psig/0.2-1.0 kg/cm2 ranges)

11B4040X042

0-60 psig/0-4 kg/cm

(6-30 psig/0.4-2.0 kg/cm2 ranges)

11B4040X052

46* Instrument Gauge, Triple Scale

0-30 psig/0-0.2 MPa/0-2 bar
(3-15 psig/20-100 kPa/0.2-1 bar ranges)

11B4040X012

0-60 psig/0-0.4 MPa/0‐4 bar
(6-30 psig/40-200 kPa/0.4-2 bar ranges)

11B4040X022

*Recommended spare parts

Содержание Fisher 3582

























































Результаты поиска

Содержание Fisher 3582

Отзывы:

Похожие инструкции для Fisher 3582

Бренды по названию

Популярные бренды

Emerson Fisher 3582, Инструкция по эксплуатации

Результаты поиска

Содержание Fisher 3582

Отзывы:

Похожие инструкции для Fisher 3582

Бренды по названию

Популярные бренды