Emerson Dixell XRB Скачать руководство пользователя страница 21

Страница: 21 / 38

1592038420 XRB30-60-70-77CH EN v1.1 2021.09.15

XRB

21/38

The device uses special

nergy

eduction

lgorithms (par.

ErA

) to optimize loads activation during the

regulation. It is possible to set two different algorithms (

ErA=bAS or Aut).

They differ for the used sensors

and for the total length of the intervals involved.

10.1 BASIC ENERGY SAVING ALGORITHM

– ERA=BAS

This will be used when

ErA=bAS

. The energy saving status will be always saved in the internal memory to

resume previous operation if a power failure occurs. It needs the presence of a door switch to work
(

i1F=dor

10.1.1 PARAMETER INVOLVED AND SUGGESTED VALUES

ErA = bAS

i1F = dor

StE

= 4.0 hours

EtS

= 6.0 hours

HES

= 3.0 to 5.0 °C

HYE

= 3 to 4°C

= 5 to 10 sec

LdE = Y

for having light output automatically OFF when energy saving mode starts.

FROM

CHANGED BY

Normal mode

Energy

Saving

- Keeping the

DOWN

button pressed for 3 sec (if enabled).

- Door continuously closed for the

StE

time.

- Number of motion events detected during

StE

interval minor than

nES

Energy

Saving

Normal mode

- Keeping the

DOWN

button pressed for 3 sec (if enabled).

- Controller in ES mode for the

EtS

time without any door opening or

with motion events detected minor than

nES

- If the controller is in ES mode, it returns in Standard mode (normal set-
point) after opening the door more than

time.

- If the controller is in ES mode, it returns in Standard mode (normal set-
point) after detecting

nES

motion events.

NOTE:

the cycling mode (ES - Normal mode - ES - etc.) works if

i1F=dor

and

EtS

and

StE

are different from

zero. If

EtS=0

StE=0,

the controller will not change the operating mode, and it will be possible to change

from the normal mode to the energy saving mode by using ES button or by setting

i1F=ES

. See the below

diagrams where the status changing is depicted:

10.1.2 INTERACTION WITH OTHER SENSORS

The following table indicates the interaction between energy saving mode (

ErA=bAS

) and various digital

input functions.

i1F

i2F

MSF

How it works

dor

Any

≠

EMt

Any

The function of digital input 1 changes the ES status according to par.

EtS

and

StE

or after opening the door for a time greater than

dor

Any

Digital input 1 has priority. The function of the second digital input is
disabled.

Содержание Dixell XRB







































Результаты поиска

Содержание Dixell XRB

Отзывы:

Бренды по названию

Популярные бренды

Emerson Dixell XRB, Инструкции по установке и эксплуатации

Результаты поиска

Содержание Dixell XRB

Отзывы:

Бренды по названию

Популярные бренды