1592025980 XEV20D GB r.2.7 31.07.2019
XEV20D
1/5
QUICK REFERENCE GUIDE
XEV20D
- FW REL. 2.5 -
CONTENTS
CONTENTS ____________________________________________________________________________ 1
GENERAL RECOMMENDATIONS ______________________________________________________ 1
COMPATIBILITY OF USE _____________________________________________________________ 1
GENERAL RULES __________________________________________________________________ 2
INSTALLATION AND MAINTENANCE ___________________________________________________ 2
MAXIMUM POWERS ALLOWED _______________________________________________________ 3
SPECIFICATIONS __________________________________________________________________ 3
WIRING DIAGRAMS _________________________________________________________________ 3
CONNECTION TO XEC SUPERCAP ____________________________________________________ 4
SERIAL -- CAN BUS LINE ____________________________________________________________ 5
MEANING OF THE LED LIGHTS _______________________________________________________ 5
1.
GENERAL RECOMMENDATIONS
Please read before using this manual any further.
•
This manual is an integral part of the product and must be kept close to the
device for quick and easy consultation.
•
The regulator must not be used for purposes other than those described below,
and it especially cannot be used as a safety device.
•
Check application limits before proceeding.
•
Dixell S.r.l. reserves the right to change the composition of its products, even
without notice, ensuring the same and unchanged functionality.
1.1 SAFETY PRECAUTIONS
•
Symbol
warns the user about the presence of non-insulated "dangerous
voltage" inside the product area, which may cause electric shock.
•
Symbol
warns the user about the presence of important operating and
maintenance (assistance) instructions found in the documentation attached to the
device.
•
Dixell Srl reserves the right to vary the composition of its products without prior notice
to the customer, ensuring the identical and unchanged features of the same.
•
This manual is part of the product and must always be kept near the device for easy
and quick reference. The device cannot be used as a safety device. Verify the limits
of application before using the device.
•
Verify that the power supply voltage is correct before connecting the device. Do not
expose it to water or humidity. Use the controller only within the operating limits,
avoiding sudden temperature changes and high atmospheric humidity, which may
result in the formation of condensate.
•
Warning: disconnect all the electric connections before performing maintenance.
Insert the probe where it cannot be reached by the End User. The device must not be
opened. Consider the maximum current that can be applied to each relay.
•
Make sure that the wires for the probes, the loads and the electrical power supply are
separated and sufficiently distant from each other, without crossing or intertwining
with each other. In the case of applications in industrial environments, it may be
useful to use the main filters in parallel with the inductive loads.
•
The customer shall bear full responsibility and risk for product configuration in order to
achieve the results pertaining to installation and/or final equipment/system. Upon the
customer's request and following a specific agreement, Dixell S.r.l. may be present
during the start-up of the final machine/application, as a consultant, however, under
no circumstances can the company be held responsible for the correct operation of
the final equipment/system.
•
Since
Dixell
products
form
part
of
a
high
level
of
technology,
a
qualification/configuration/programming/commissioning stage is required to use them
as best as possible. Otherwise, these products may malfunction and Dixell cannot be
held responsible. The product must not be used in any way that differs from that
stipulated in the documentation.
•
The device must always be inserted inside an electrical panel that can only be
accessed by authorized personnel. For safety purposes, the keyboard must be the
only part that can be reached.
•
The device must never be hand-held while being used.
•
It is good practice to bear the following in mind for all Dixell products:
o
Prevent the electronic circuits from getting wet as contact made with water,
humidity or any other type of liquid can damage them. Comply with the
temperature and humidity limits specified in the manual in order to store the
product correctly.
o
The device must not be installed in particularly hot environments as high
temperatures can damage it (electronic circuits and/or plastic components
forming part of the casing). Comply with the temperature and humidity limits
specified in the manual in order to store the product correctly.
o
Under no circumstances is the device to be opened - the user does not require
the internal components. Please contact qualified service personnel for any
assistance.
o
Prevent the device from being dropped, knocked or shaken as either can cause
irreparable damage.
o
Do not clean the device with corrosive chemical products, solvents or
aggressive detergents.
o
The device must not be used in applications that differ from that specified in the
following material.
Separate the power supply of the device from the rest of the electrical
devices connected inside the electrical panel. The secondary circuit of
the transformer must never be connected to the earth.
1.2 PRODUCT DISPOSAL (WEEE)
With reference to Directive 2002/96/EC of the European Parliament and of the
Council of 27 January 2003 and to the relative national legislation, please note that:
•
There lies the obligation not to dispose of electrical and electronic waste as
municipal waste but to separate the waste.
•
Public or private collection points must be used for disposal, in accordance with
local laws. Furthermore, at the end of the product's life, it is also possible to
return this to the retailer when a new purchase is made.
•
This equipment may contain hazardous substances. Improper use or incorrect
disposal can have adverse effects on human health and the environment.
•
The symbol shown on the product or the package indicates that the product
was placed on the market after 13th August 2005 and must be disposed of as
separated waste.
•
Should the product be disposed of incorrectly, sanctions may be applied as
stipulated in applicable local regulations regarding waste disposal.
2.
COMPATIBILITY OF USE
2.1 MAIN FEATURES
XEV20D
is a
bipolar
or
unipolar
motorized driver (Stepper) for electronic expansion
valves. This driver is developed for use in combination with the
ISaGRAF®
environment and programmable devices in the
iPRO series.
The main features are:
•
controlling one or two electronic expansion valves:
•
compatibility with various valve models
•
compatibility with various types of refrigerant
•
manual adjustment (PID) or self-adaptive overheating
•
4 analogue inputs
•
Can Bus for ipro connection
In case of 2 expansion valves they MUST HAVE the same STEP
RATE.
2.2 CONNECTIONS / INSTALLATION
The devices must not be installed in environments where the following situations are
present:
➢
Temperature and humidity out of the range stipulated in the instrument
label. Frequent and sudden changes in temperature and/or humidity.
➢
Direct sunlight and weathering in general
➢
High mechanical stress (vibrations and/or impact)
➢
Sulphur and ammonia gas, smoke and salt spray that can cause
corrosion and/or oxidation
➢
Presence of flammable or explosive gas
➢
Dust
➢
Devices that generate electromagnetic interference
Place the device inside the electrical panels, paying attention to the following:
➢
the distance between the device and the electrical power components
➢
the distance between the device and the power cables
➢
sufficient space for the cooling air
Always comply with the laws and regulations applicable in the country where the
device is installed.
Always protect the device for it to always be accessible solely by authorized
personnel.
In case of malfunctions, always contact the relative distributor for the device to be
repaired.