Emerson Dixell XC645D Скачать руководство пользователя страница 27

Страница: 27 / 50

1592001830 XC645D GB r3.4 04.09.2017.docx XC645D

27/50

17.10 Alarms

– fans section

LAF

Low pressure alarm

– fans section

: The measurement unit depends on the dEU

parameter: (FA04 ÷ HAF bar; -50.0÷HAF °C; FA04÷HAF PSI; -58÷HAF °F)

It’s

independent from the set point. When the value LAF is reached the LA2 alarm is enabled,
(possibly after the

AFd

delay time).

HAF

High pressure alarm

– fans section

: The measurement unit depends on the dEU

parameter: (LAF÷FA20 bar; LAF÷150.0 °C; LAF÷FA20 PSI; LAF÷302 °F).

It’s

independent from the set point. When the value HAF is reached the HA2 alarm is enabled,
(possibly after the

AFd

delay time).

AFd

Low and High pressure alarms delay

– fans section

: (0÷255 min) time interval

between the detection of a pressure alarm condition in the fans section and alarm
signaling.

HFC

Compressors off with high pressure (temperature) alarm for fans

= compressors are not influenced by this alarm

yES

= compressors are turned off in case of high pressure (temperature) alarm of fans

HFdP Digital Compressor Capacity percentage in case of high condenser pressure

(temperature) alarm

(0÷80%; with 0 the compressor is stopped)

dHF

Interval between 2 compressors turning off in case of high pressure (temperature)
alarm for fans

(0 ÷ 255 sec)

PnF: High pressure-switch intervention numbers

– fans section:

(0÷15 with 0 the manually

unlocking is disabled) if the high pressure-switch is enabled PnF times in the PiF interval,
the controller is locked.

It can be unlocked only manually

. See paragraph 0. Every time

the pressure-switch is enabled all the compressors are turned off and all the fans are
turned on.

PiF:

Pressure-switch interventions time

– fans section

(1÷15 min) Interval, linked to the

PEn parameter, for counting interventions of the high pressure-switch..

FPr

Number of fans engaged with faulty probe

. (0÷#fans).

17.11 Suction superheat

ASH0 Differential for low superheat pre-alarm.

(

0.1 to 30.0°C/ 1 to 60°F).

The low superheat pre-alarm warning is sent when the superheat (SH) is lower than ASH2
(low superheat alarm threshold) + ASH0, possibly after the ASH1 delay.

ASH1 Delay for signalling low superheat pre-alarm

(0÷255sec)

If the superheat is below the ASH2+ASH0 threshold for ASH1 time the low superheat
pre-alarm warning is sent.

ASH2 Low suction superheat alarm threshold (

0.1÷15.0°C/ 1÷30°F). With SH < ASH2 the

low superheat alarm is sent, possibly after the ASH3 delay

ASH3 Delay for signalling low superheat alarm

(0÷255sec)

If the superheat is below the ASH2 threshold for ASH3 time the low superheat alarm
message is sent.

ASH4 Switching off compressors with low superheat alarm

(No, Yes)

ASH4 = no: compressors keep on working even with low superheat alarm.

ASH4 = yES: compressors are stopped in case of low superheat alarm.

ASH5 Differential to restart regulation after of low superheat alarm with compressor stop

(0.1 to 15.0°C/ 1 to 30°F). In case of regulation stop (ASH4= yES), it restarts when SH >
ASH2+ASH5

ASH6 Delay to restart regulation after superheat > ASH2+ASH5 (

0÷255 min). If the

regulation is stopped because of low superheat alarm, it can restart when
SH>ASH2+ASH5 for the ASH6 time.

ASH7 Superheat value to enable hot gas injecting valve (

0.1 to 15.0°C/ 1 to 30°F)

With a relay set as hot gas injection valve, (oA2 or oA3 or oA4 = HGi), the relay is on with
SH < ASH7

– ASH8.

ASH8 Differential for ASH7

(

0.1 to 30.0°C/ 1 to 60°F)

Содержание Dixell XC645D



















































Результаты поиска

Содержание Dixell XC645D

Отзывы:

Emerson Dixell XC645D, Инструкции по установке и эксплуатации, Страница: 27 / 50

Результаты поиска

Содержание Dixell XC645D

Отзывы: