background image

7.

Insert the ceiling fan support cable from the fan through
the brass nut and reinstall the machine screw. Tighten
the machine screw securely (Figure 5). Be sure the steel
support cable is securely tightened before proceeding
with installation.

INSTALLATION NOTE: 

Check all fasteners and retighten

where necessary before continuing with the installation of
the ceiling fan.

8.

To complete fan assembly, proceed to “How to Wire
Your Ceiling Fan” in the Ceiling Fan Instructions Manual.

Form No. BP7410
Part No. F40BP74100000

10/09

Air Comfort Products

DIVISION OF EMERSON ELECTRIC CO.

8100 W. Florissant • St. Louis, MO 63136

5.

Install the assembled ceiling fan onto the mounting
bracket in accordance with the instructions provided with
the ceiling fan.

6.

Unscrew the machine screw from the brass nut (supplied)
and feed the end of the ceiling fan support cable from the
ceiling fan downrod through the loop on the end of the
short steel support cable (Figures 4 and 5).

BRASS 
NUT

MACHINE SCREW

CEILING FAN 
SUPPORT 
CABLE

MACHINE 
SCREW

DRYWALL CEILING

ELECTRIC SUPPLY 
WIRES OMMITED 
FOR CLARITY

OUTLET BOX

SHORT STEEL 
SUPPORT CABLE

BRASS NUT

CEILING FAN 
SUPPORT CABLE

SHORT STEEL 
SUPPORT CABLE LOOP

CEILING 
COVER

CEILING FAN 
SUPPORT CABLE

CEILING 
COVER

HANGER BRACKET

HANGER BALL

SHORT STEEL UPPER SUPPORT CABLE

Figure 3

Figure 4

Figure 5

Содержание CORSAIR 44"















Отзывы: