background image

10

Operation

IMPORTANT

Fan installation must be completed, including the
installation of the fan blades, before testing of the
remote control.

Your remote control has full control of your fan and
lights.

NOTE: Prior to operation of the down light from
the remote control, make sure the switch on the
light is ON.

1. To set the desired fan speed, press the HI, MED,

or LOW button to operate your fan on high,
medium, or low speed.

2. To turn your fan off, press the OFF button.

3. To change the airflow direction of the fan blades,

press the REV button.

4. To turn the downlight on, press and release the D/L

button. The light will turn on at the light intensity
previously selected.

5. To turn the uplight on, press and release the U/L

button. The light will turn on at the light intensity
previously selected.

6. To vary the intensity of the light, hold the U/L or D/L

button down until the desired light intensity is
reached, then release the button.

Accessories

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or acces-
sories not designated for use with this product by
Emerson Company could result in personal injury or
property damage.

The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.

1. Ceiling Fan Light Kits (see store or catalog).

2. Downrod Extension Kits (see store or catalog).

WARNING

!

WARNING

!

REV

MED

OFF

HI

LOW

U

L

D

L

®

STORAGE
BRACKET

IMPORTANT CARE INSTRUCTIONS

for your Ceiling Fan

Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.

When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.

Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.

Maintenance

Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.

WARNING

!

Installation of

Storage Bracket

A storage bracket is supplied with the remote control
for holding the control unit when not in use. If you
desire to use the bracket, use the two screws
(supplied) and install it on a wall that is away from
excess heat or humidity.

Содержание CF945AB













Отзывы: