Emerson Bettis GTD Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 37

background image

Service Instructions

133893 Rev. C

January 2013

6

Section 2: Actuator Disassembly

Actuator Disassembly

2.3.3

Remove the jam nut (7-190) from stop screw (7-180).

2.3.4

Remove stop screw (7-180) from outer end cap (7-80).

2.3.5

Remove hex nuts (7-90), with lockwashers (7-95), from tie bars (7-20).

2.3.6

Remove outer end cap (7-80) from cylinder (7-70) and tie bars (7-20).

2.3.7

Unscrew and remove tie bars (7-20) from inner end cap (7-10).

2.3.8

Remove the cylinder (7-70) from piston (7-30) and inner end cap (7-10).

2.3.9

Refer to assembly drawing page 2 of 2 Detail "E". Remove two split ring halves (7-
50) and one retainer ring (7-60) from outboard end of piston rod assembly (7-40).

2.3.10  Remove the piston (7-30) from piston rod assembly (7-40).
2.3.11  Remove the o-ring seal (8-70) from piston rod assembly (7-40).
2.3.12  Remove the remaining two split ring halves (7-50) and one retainer ring (7-60)

from piston rod assembly (7-40).

2.3.13 Remove socket cap screws (7-115) with lockwashers (7-110) from

inner end cap (7-10).

2.3.14 Refer to assembly drawing page 2 of 2 Detail "D". Remove hex nuts (7-105) from

socket cap screws (7-100).

2.3.15 Remove socket cap screws (7-100) with lockwashers (7-110) from

inner end cap (7-10).

2.3.16  Remove inner end cap (7-10) off of piston rod assembly (7-40).
2.3.17  Unscrew and remove piston rod assembly (7-40) from drive module.
2.3.18  It is not necessary to remove pipe plugs (7-210) from inner end cap (7-10) and

outer end cap (7-80) for normal or routine actuator service.

2�4

Drive Module Disassembly

NOTE:

Review Section 2 notes and steps 2.1.1 through 2.1.5 General Disassembly before proceed-
ing with Drive Module Disassembly.

2.4.1

If not already removed remove piston rod assemblies (3-40) and (7-40) from drive
module (1-10).

NOTE:

For steps 2.4.2 through 2.4.9 refer to assembly drawing page 2 of 2 Section A-A and Detail “A”.

2.4.2

Before removing position indicator (1-220), record or mark it's position. Remove
position indicator (1-220).

NOTE:

Step 2.4.3 is used only on GTD01, GTD2 and GTD3 Drive Modules. Drive Modules GTD4
and GTD5 will skip steps 2.4.3 and continue with step 2.4.4.

«
...
7
8
9
10
11
...
»

Содержание Bettis GTD Series






































Отзывы:

Нет отзывов

Похожие инструкции для Bettis GTD Series

Бренд: IBM Страницы: 144

Бренд: Taie Страницы: 28

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: bihl+Wiedemann Страницы: 16

Tracer CH.530 RLC-SVU01B-E4

Бренд: Trane Страницы: 60

Бренд: RKC INSTRUMENT Страницы: 10

Бренд: ISVT Страницы: 78

Бренд: Linear Technology Страницы: 8

Бренд: Precision Страницы: 8

TRAP-SHUFFLE Game Simulator

Бренд: RF SOLUTIONS Страницы: 2

Infi 90 IMSPM01

Бренд: Bailey Страницы: 52

Dual Motor Focus Controller

Бренд: Pegasus Astro Страницы: 16

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Бренд: DS Produkte Страницы: 4

Бренд: GEM Страницы: 56

Бренд: Lunt Solar Systems Страницы: 4

Бренд: SainSmart Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды