background image

4

k. One loose parts bag containing:

1. Two 1-1/4” threaded studs
2. Two knurled knobs
3. Two lockwashers
4. Three wire connectors
5. One clevis pin
6. One hairpin clip
7. Eleven M5 x 16mm oval

head screws

8. Sixteen M5 x 6mm slotted

Phillips washer head screws

NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost. 

2. Remove the fan motor and housing

uplight assembly from the protective
plastic bag. Place the fan motor and
housing uplight assembly on a padded
work surface with the bottom of the
motor facing up.

IMPORTANT: Remove the two card-
board retainers from between the
housing uplight and the motor
housing.

E

F

G

I

B

C

K

EMERSON

®

HI

MED

LOW

FAN  OFF

LIGHT

ON

OFF

J

H

A

D

Your new ceiling fan will require a
grounded electrical supply line of 120 volts
AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored
and capable of withstanding a load of at
least 50 pounds.

To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.

!

WARNING

If your fan is to replace an existing ceiling
light fixture, turn electricity off at the main
fuse or circuit breaker box at this time and
remove the existing light fixture.

Electrical Requirements

Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.

!

WARNING

IMPORTANT: Your ceiling fan will not
function properly, and may be
damaged, if used with any wall dimmer
switch or control other than the
Emerson Electric SW101 Fan/Light Wall
Control supplied with the fan, or an
optional Emerson Electric SR100
Remote Control.

BP7309 BANFF  1/5/06  9:59 AM  Page 4

Содержание BANFF CF720ORB00

















Отзывы: