Emerson ASCO 300 Series Скачать руководство пользователя страница 3

Страница: 3 / 20

ASCO Series 300 Automatic Transfer Switches (ATSs) are

Listed under Underwriters Laboratories UL 1008 Standard

for Safety for Automatic Transfer Switches. All control

features are UL Component Recognized, which assures that

ASCO automatic transfer switches meet OSHA Safety

Requirements and will be acceptable to electrical inspectors.
ASCO Series 300 Automatic Transfer Switches are suitable

for emergency and standby system applications. They meet

emergency system rating requirements as defined in

National Electrical Code (NEC) Article 700 and UL 1008.

Also, they are suitable for the requirements of NEC Article

517 – Health Care Facilities, NEC Article 701 – Legally

Required Standby Systems, NEC Article 702 – Optional

Standby Systems, NFPA 99 Health Care Facilities, and

NFPA 110 Emergency and Standby Power Systems.

Rating Label

Each automatic transfer switch contains a rating label to

define the loads and fault circuit withstand / closing ratings.

Refer to the label on the transfer switch for specific values.

Do not exceed the values on the rating label.

Exceeding the rating can cause personal injury

or serious equipment damage.

terminal block TB

for engine start

and switch

position contacts

Transfer

Switch

Controller

power

connections

power

connections

membrane

controls

800 and 1000 amp. size in typical enclosure with location of customer connections

neutral

connections

neutral

connections

Содержание ASCO 300 Series





















Результаты поиска

Содержание ASCO 300 Series

Отзывы:

Похожие инструкции для ASCO 300 Series

Бренды по названию

Популярные бренды

Emerson ASCO 300 Series, Руководство оператора

Результаты поиска

Содержание ASCO 300 Series

Отзывы:

Похожие инструкции для ASCO 300 Series

Бренды по названию

Популярные бренды