background image

Special Conditions for Safe Use (X):

1. The enclosure’s polyurethane paint finish may constitute an

electrostatic hazard. Care should be taken to protect it from external
conditions conducive to the build-up of electrostatic charge on such
surfaces. The equipment must only be cleaned with a damp cloth.

2. The non-intrinsically safe Supply, Modbus RTU & Ethernet Port

connections of the equipment must be supplied from either safety
extra low-voltage (SELV) or protective extra low-voltage (PELV)
circuits, for example equipment complying with the requirements of
either the IEC 60950 series, IEC 61010-1 or a technically equivalent
standard.

3. The equipment is not capable of withstanding the 500V electrical

strength test as defined in clause 6.1 of EN 60079-7:2015+ A1:2018
and 6.3.13 EN 60079-11:2012. This must be taken into account
during installation.

7.2.7

International

N7 IECEx Increased Safety with Intrinsically Safe Output to Zone 0

Certificate

IECEx BAS.20. 0022X

Markings

Ex ec [ia Ga] IIC T4 Gc (-40 °C ≤ T

a

 ≤ +65 °C)

Standards

IEC 60079-0: 2017, IEC 60079-7:2015+A1:2017, IEC
60079-11: 2011, IEC 60079-15:2017, IEC 60079-31:2013

N7 IECEx Increased Safety with Intrinsically Safe Outputs to Zone 0 (For
use only with the Cisco Outdoor Access Point Model IW-6300H-AC-x-K9)

Certificate

IECEx BAS.20. 0022X

Markings

Ex ec nA [ia Ga] IIC T4 Gc (-40 °C ≤ T

a

 ≤ +65 °C)

Standards

IEC 60079-0: 2017, IEC 60079-7:2015+A1:2017, IEC
60079-11: 2011, IEC 60079-15:2017, IEC 60079-31:2013

Special Conditions for Safe Use (X):

1. The enclosure’s polyurethane paint finish may constitute an

electrostatic hazard. Care should be taken to protect it from external
conditions conducive to the build-up of electrostatic charge on such
surfaces. The equipment must only be cleaned with a damp cloth.

2. The equipment is not capable of withstanding the 500V electrical

strength test as defined in clause 6.1 of EN 60079-7:2015+ A1:2018
and 6.3.13 EN 60079-11:2012. This must be taken into account
during installation.

July 2022

Quick Start Guide

Quick Start Guide

35

Содержание 1410S













































Отзывы: