Emerson Quiet Kool EBTC08RE1T Скачать руководство пользователя страница 14

9

                       When the unit is in ECO mode, the 

light will turn on. In ECO mode, the unit will 

turn-off once the room is cooled to the user set 

temperature. The fan will also be off at this point. 

The unit will turn back on when the room 

temperature rises above the user set temperature.

Before the compressor stars, the fan motor will 

run for a while, then it will stop for a while-and will 

repeat to provide a much more comfortable-feeling 

and save energy.

6.

Eco Button:

                          Press the SLEEP button, the Sleep 

Light will be on after 10s, and all the left lights will 

be off. In SLEEP mode, the air-conditioner will 

automatically adjust the temperature and fan 

speed to make the room more comfortable during 

the night. For cooling mode, the set temperature 

will automatically raise by 1

 every 30-60 minutes 

and at most change six times until the set 

temperature is 28

. For heating mode, the set 

temperature will automatically decrease by 1

 

every 30-60 minutes and at most change six times 

until the set temperature is 24

.  

And every running time depends on the set 

temperature.

7.

Sleep Button:

                                   Press the FAN SPEED button 

to choose the fan speed options. You can choose 

Hi, Med, Lo or auto speed in COOL mode and 

choose Hi, Med, Lo in FAN mode.

8.

Fan Speed Button:

9.                          When the Filter Check light is off, 

it is useless to press the Filter Check button. When 

the Filter Check light is on, it can turn off the light 

by pressing the Filter Check button. After the 

fan motor works for 500 total hours, the Filter 

Check light will turn on to remind the user to clean 

the filter.

Filter Button:

10.                                       To direct the airflow,

horizontal wheel to control the horizontal direction, 

air deflector to control the vertical direction.

Directional Louvers:

horizontal wheel

air deflector

air deflector

Содержание EBTC08RE1T





















Отзывы: