manualshive.com logo in svg

EMC Connectrix DS-24M2, Руководство по установке, Страница: 13 / 14

Поделиться
Скачать
EMC Connectrix DS-24M2 Скачать руководство пользователя страница 13

EMC Departmental Switch DS-24M2  Installation Guide

13

Installing Latch Brackets or Ball Studs

Installing Latch Brackets or Ball Studs

This section describes how to install latch brackets (for a 40U cabinet) 
or ball studs (for a 39U cabinet). Latch brackets and ball studs 
support the bezel. 

1. If you are installing the switch in a 40U cabinet, install the latch 

bracket in the center hole, over the keyplate spacer, using a

 

#10 

32x5/8” pan-head screw. See the figure below.

If you are installing the switch in a 39U cabinet (either in a round-hole 
or square-hole channel),

 

position the

 

#10 washer and ball stud in the 

center hole, between the two #10 32x5/8” flat-head screws. 
Tighten the ball stud. See the figure below.

2. Repeat step 1 with the other side of the channel.

3. Attach the bezel to the front of the cabinet by lining the bezel up 

with the latch brackets (40U) or ballstuds (39U) until the bezel 
snaps into place.

EMC2488

Latch
Bracket

Screw

Keyplate
Spacer

EMC2491

Ball
Stud

#10 Flat
Washer

Содержание Connectrix DS-24M2















Отзывы:

Нет отзывов