Embedded Artists iMX RT1062 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 40

Embedded Artists iMX RT1062 Скачать руководство пользователя страница 38

iMX RT1062 OEM Developer’s Kit - User’s Guide

Page 38

Copyright 2019 © Embedded Artists AB

5

Troubleshooting

This chapter contains information about how to troubleshoot boards that does not seem to operate

properly. It is strongly advised to read through the list of tests and actions that can be done before

contacting Embedded Artists. The different tests can help determine if there is a problem with the

board, or not. For return policy, please read Embedded Artists’ General Terms and Conditions
document (can be found at

http://www.embeddedartists.com/shop/

).

5.1

No SWD/JTAG Connection

Note that JP5 shall not be shorted/inserted. Verify correct orientation when using the Cortex Debug

connector (2x5 pos, 50 mil pitch connector).

5.2

Powering

The first step is to make sure that powering works properly.

1.

Make sure all jumpers are in default position, see section 4.16 for details.

2.

Power the board via the micro-AB USB connector, J22, also known as position 1) in Figure 1.

3.

Verify that you can measure 5V +-0.3V on the jumper in J29 and that LED2 is on.

4.

Verify that you have 3.2V - 3.4V on any of the pins of J4. This is the always-on voltage

supply. Verify that the voltage measured over J4 is less than 25 mV.

5.

Verify that you have 3.3V +-0.15V on any of the pins of J3. This is the main voltage supply.

Also verify that LED3 is on.

Verify that the voltage measured over J3 is less than 50 mV.

6.

Press the reset push-button, SW3. Verify that LED3 is off while pressing SW3.

7.

Press the ON/OFF push-button, SW2, for 5 seconds. Verify that LED3 is turned off after the 5
seconds. Press the button again for a short while and LED3 will turn on again.

5.3

Contact with OEM Board MCU

The second step is to make sure it is possible to download an application to the i.MX RT1062 MCU on

the

OEM Board

is working. Follow the instructions found in the

iMX RT1062 Developer's Kit Program

Development Guide

to download the demo application. This can be used without a debug probe.

Alternatively download any of the sample applications via any of the supported IDEs.
This test verifies that the i.MX RT1062 is operating properly.

5.4

Using the Demo Application to Verify Correct Operation

The third step is to run the just downloaded demo application. There are many tests that can be
performed, one after one, to verify correct operation of individual parts of the

iMX RT1062 OEM Board

as well as the

iMX OEM Carrier Board

. While doing these tests, be sure to not have any interfering

circuits connected to the access pads.

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

Downloaded from

«
...
36
37
38
39
40
»

Содержание iMX RT1062









































Отзывы:

Нет отзывов