1. IMPORTANT SAFETY INSTRUCTIONS
The user guide you are holding includes essential information on the safety measures to be implemented for
installation and start-up. Therefore, the installer as well as the user must read the instructions before beginning
installation and start-up. Keep this manual for future reference.
The pump should be installed according to your local electrical installation ordinances and regulations. Only
qualified, licensed personnel should install the pump and the wiring.
This appliance cannot be used by persons (including children) with reduced physical, sensor y or mental
capabilities or lack of experience and knowledge unless they have been given super vision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with
the appliance.
IMPORTANT SAFETY INSTRUCTIONS P4
Correct disposal of this product
This symbol on the product, or in its packaging, indicates that this product
may not be treated as household waste. Instead, it should be taken to the
appropriate waste collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment
and human health, which could other wise be caused by the inappropriate
waste handling of this product. For more detailed information about the
recycling of this product, please contact your local council, your household
waste disposal ser vice, or the shop where you purchased the product.
2. INSTALLATION
1. Install the pump as close to the pool as possible, preferably in a dr y, well ventilated area away from direct sun
light. Protect the pump from excessive moisture.
2. Place the pump as close to the water source as possible, so that the suction pipe is short, straight and direct
to reduce the friction loss. Don't install the pump at more than 10ft (3 meters) of geometrical height from
water level.
3. Before installing the pump, make sure that the surface is solid, elevated, rigid and vibration free.
4. Secure the pump to the base with screws or bolts to limit the vibration and the stress on the pipe or the joints.
5. Leave enough space for gate valves in suction and discharge piping, if required.
6. Connect the suction and discharge pipe to the outlet and inlet of the swimming pool.
7. Make sure that floor drainage is adequate to prevent flooding.
8.
This pump must be equipped with an isolating
transformer or through a residual current device
(RCD) having a rated residual operating current not
exceeding 30 mA.
9. Make sure that the pump and piping are accessible
for ser vicing.
Note: The pump suction and discharge connections are
mounded in thread stops, DO NOT tr y to screw the
pipe beyond these stops.
15. REPLACEMENT PARTS
Key No.
Part No.
Description
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
18
19
20
21
22
01021143
01041057
02010253
01112080
89023801
01021144
89021307
02010245
01112081
89020719
01311058
04015065
02010246
01021145
89020720
03011075
04020140
01112082
02010211
01031027
01321032
89023901
01041061
Nut for lid
Transparent Lid
O-Ring for Lid
Basket
1.5" Union
Pump Body
Drain Plug with O-ring
Diffuser
Screw for impeller with O-Ring
O-Ring for Flange
Flange
M8 x 35 Screw with Washer for Motor
M8 x 30 Screw
Base
O-Ring for Diffuser
Impeller For SPV150 & EPV150
3/4
″
Mechanical seal (EPH/EPV/SPH/SPV)
SPV150 TYC-71L Motor
Arch Cushion for Base
Fan
Fan Cover
Programmable Controller for SPV150
Transparent Lid for Programmable Controller
1
1
1
1
2
1
2
1
1
1
1
1
1
1
4
4
1
1
1
1
1
1
1
P19 REPLACEMENT PARTS
20
1
2
3
4
5
8
9 10 11 12
13 14
15
21
22
16
7
18
6
17
19
