WARNINGS AND SAFETY INSTRUCTIONS
GENERAL WARNING
This instruction contain general caution information for use in Pool and SPA pump installation application.
Specified Pump model function should be refer to particular manual. Components such as the filtration system,
pumps and heater must be positioned so as to prevent their being used as means of access to the pool by young
children.
This appliance should be installed by qualified electrical personnel in
accordance with National Electrical Code and all applicable local codes
and ordinances. Hazardous voltage can shock , burn, and cause death or
serious property damage. DO NOT use an extension cord to connect unit
to electric supply to reduce the risk of electric shock .
1
.
The pump should be permanently connected to an individual circuit breaker.
2
.
Pump must be connected to a residual current device (RCD) having a rated residual operating current not
exceeding 30 mA or receptacle with ground fault circuit interrupt (GCFI).
3. Electrical grounding must be connected before connecting to electrical power. Failure to ground all electrical
equipment can cause serious or fatal electrical shock hazard.
4
.
Bonding: Use at least #8 AWG (#6 AWG for Canada) a solid copper conductor, run a continuous wire from
external bonding lug (if available) to the pressure wire connector provided on the electrical equipment and to
all metal parts of swimming pool, spa, or hot tub, and metal piping (except gas piping), and conduit within 1.5
m (5 ft) of inside walls of swimming pool, spa, or hot tub.
5
.
Never open the inside of the drive motor enclosure. There is a capacitor bank that holds a mains supply
voltage charge even when there is no power to the unit. The voltage should be referred to the individual
pump operation voltage.
6
.
The pump is capable of high flow rates; use caution when installing and programming to limit pumps
performance only.
7
.
Switch OFF pump power before ser vicing and disconnecting the main circuit to the pump.
8
.
Never change the filter control valve position while the pump is running.
RISK OF ELECTRICAL SHOCK
COMPRESS AIR HAZARDOUS
This system enclosed pre-filter / filter and become pressurized.
Pressurized air can cause the Lid to separate which can result in serious
injur y or death.
Pool and spa circulation systems operate under high pressure. When any
part of the circulating system (i.e. lock ring, pump, filter, valves, etc.) is
ser viced, air can enter the system and become pressurized. Filter tank Lid and pre-filter cover must be properly
secured to prevent violent separation. Place pre-filter / filter air relief valve in the open position and wait for all
pressure in the system to be relieved before remove the lib to access the basket for cleaning.
HYPERTHERMIA
SPA water temperature excess 38°C (104°F) may be injurious to health.
Measure water temperature before entering SPA.
Hyperthermia occurs when the internal temperature of the body reaches
a level several degrees above the normal body temperature of 98.6 °F (37
°C). The symptoms of hyperthermia include drowsiness, lethargy, and an
increase in the internal temperature of the body.
WARNINGS AND SAFETY INSTRUCTIONS P2
Problem description
Possible causes
Leakage of water at the shaft
Shaft seal requires replacement
Low pump capacity
1. Valve in the suction or discharge line partly closed
2. Suction or discharge line partly plugged
3. Suction or discharge line too small
4. Plugged basket in skimmer or hair and lint strainer
5. Dirty filter
6. Impeller clogged
High pump pressure
1. Discharge vale or inlet fittings closed too much
2. Return lines too small
3. Dirty filters
Noisy pump and motor
1. Plugged basket in skinner or hair in lint strainer
2. Worn motor bearings
3. Valve in suction line partly closed
4. Suction line partly plugged
5. Vacuum hose plugged or too small
6. Pump not supported properly
Air bubbles at inlet fittings
1. Leakage of air into the suction line in connections or valve stem
2. Cover gasket of hair and lint strainer needs cleaning
3. Low water level in the pool
Note: If the above recommendations of this manual do not solve your particular problem(s), please contact your
local ser vice agent for further assistance.
P21 WARRANTY POLICY
18. WARRANTY POLICY
EXTENDED
WARRAN TY FOR SPECIFIC PRODUCTS
(OFFERED
FROM
DATE
OF INVOICE)
.
Product
Warranty
Period
Filters
&
Filter
Systems
2
years
Pumps
1
year
Underwater
Lights
1
year
(
bulbs
90
days
)
Ladders
1
year
Control
devices
1
year
Heat
Pumps
&
Heat
Exchangers
1
year
Salt
Chlorinators
&
UV Systems
1
year
(
2
years
for
cell
material
)
Pool
Fittings
1
year
Cleaning
Equipment
&
All
others
1
year
Emaux manufactures its products with the highest standard of workman ship, using the best materials available
through state of the art process. Emaux proudly warrants its products as follows:
