background image

 

 

CMi6140 

User’s Manual English 

 

 

 

 

 

 

 

 

 

 

 

 

CMi6140 

User’s Manual English 

page | 20 (38) 

[2022-09] 

 

V1.2 

 

 

 

 

Example 2 

A device is configured the following way: 

 

Message encoding: SenML/CBOR/M-Bus 

 

Auto upload order: FIFO 

 

Measurement interval: 60 minutes 

 

Transmit interval: 60 minutes 

 

Transmit offset: 15 minutes 

 

Transmit delay: 30 minutes 

 

Maximum uploads per transmission: 4 

 

Upload maximum age 72h 

 

Device max payload size: 12 (readouts per telegram) 

A network issue caused the module to be offline for 5 days, while still reading and storing measurement 
data. When the device manages to go online the following scenario takes place. 

 

The device will start by transmitting measurement data that is 3 days old (FIFO order) 

 

The device will send 4 measurement telegrams per hour, at a randomly chosen time between 
minute 15 and 45 

 

Each telegram contains 12 meter readouts, totaling 4 x 12 = 48 readouts per transmission 

 

The device will take approximately 2 hours to “catch up” and start sending one measurement per 
hour 

7.4 

Meter data transmissions 

CMi6140 sends meter data messages according to it

’s transmit interval settings. Meter read out is always 

related to meter’s clock at time 00:00:00. Transmission time is randomized between read outs. 
 
The user can customize the data sent from the module by configuring 

message format

 and 

encoding

 of 

the telegram.  

7.4.1  Message formats 

CMi6140 has four different message formats, Standard, Extended, Combined and Pulse. By selecting 
message format, the user can decide what the meter registers that will be included in the telegram.  
 
In message format Standard, all meter registers in Table 9 is included in the telegram. For message 
format Extended, all meter registers of Table 9 and Table 10 will be included in the message. Message 
format Combined

is covered in Table 11, and Pulse

 

in

 

Table 12.Below each message format table, the 

same message format but in JSON encoding is displayed. 
 
Standard: Message format ID 66 
 

Field 

 

Description   

 

Date and 
Time 
(see Note 1) 

  

INT32 

Date and Time (Type F), 
Example: 046Dxxxxxxxx 
M-Bus Format F for Date & Time 

Meter ID 
(see Note 1) 
(see Note 2) 

  

BCD8 

According to M-Bus EN13757-3 identification 
field 
e.g. 0C78xxxxxxxx 

Energy 

  

6-7 

INT32 

Example: 0406xxxxxxxx, 040Fxxxxxxxx 

Содержание 1100441







































Отзывы: