Eltorque QT250 Скачать руководство пользователя страница 46

Страница: 46 / 92

Operation

Page 46 of 92

User Manual QT250 and QT800 gen 2.5, ID 2021 2.3 20. April 2021

Figure 33: Manual operation of the actuator

Figure 34: Position scale

The following subsections describe what triggers an alarm, reactions from the
actuator and how the alarm is reset.

•

Trigger conditions:

One or more of the alarms POSITION UNDEFINED,

TEMPERATURE or TORQUE is active.

•

Reaction from actuator

: None for the GENERAL alarm itself, but the other

alarms that are active have reactions.

•

Reset conditions

: The alarms POSITION UNDEFINED, TEMPERATURE and

TORQUE must be inactive.

•

Trigger conditions:

The outgoing shaft of the actuator is out of range.

•

Reaction from actuator:

None besides an active alarm.

•

Reset conditions

: The outgoing shaft must be run back within range.

Valve percent position is a [0%, 100%]

value. A value of 0% corresponds to the

CLOSED position

, while a value of 100% corresponds to the

OPEN position

. Seen

Содержание QT250





























































































Результаты поиска

Содержание QT250

Отзывы:

Похожие инструкции для QT250

Бренды по названию

Популярные бренды

Eltorque QT250, Руководство пользователя

Результаты поиска

Содержание QT250

Отзывы:

Похожие инструкции для QT250

Бренды по названию

Популярные бренды