ELTEX TAU-4.IP Скачать руководство пользователя

Страница: 163 / 190

163

VoIP Subscriber Gateways

Command mode

EXEC

Example

tau-8# upgrade image 192.168.118.46 tau24.img

update_tftp_fw.sh: set TFTP IP to 192.168.118.46

rm: cannot remove '/tmp/syslog.trace': No such file or directory

update_tftp_fw.sh: downloading IMG filename:

update_tftp_fw.sh: Copy bin files in /tmp/bin

tau-8#

configure

The command is intended for enter the configuration mode.

Syntax

сonfigure

Parameters

Command contains no arguments.

Privilegy

priv

Command mode

EXEC

Example

tau-8# configure

tau-8(config)#

Configuration level commands

network

The command is intended for enter the network interface configuration mode.

Syntax

network

Parameters

Command contains no arguments.

Privilegy

priv

Command mode

CONFIG

Example

tau-8(config)# network

tau-8(config-net)#

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды