ELTEX TAU-4.IP Скачать руководство пользователя

Страница: 130 / 190

130

VoIP Subscriber Gateways

APPENDIX C. THE USE OF COMMAND LINE INTERFACE (CLI) FOR CONFIGURATION AND MONITORING

Configuration changes, performed by CLI, will be applied after device

reboot

(except for IPTV settings). To apply changes, restart PBX (

pbx restart

). All the

current calls will be dropped.

To save changes into the device non-volatile memory, execute the

save

command.

CLI has two modes:



privileged — available for 'admin' profile. The mode allows you to get full access to the device configuring, trouble-shooting and monitoring;



unprivileged – available for 'admin' and 'user' profiles. The mode provides narrow set of the options for the device monitoring and trouble-shooting.

Table C.1 — CLI commands

Command

Value

Privilegy

Description

No command function

quit

none

Completes the
current CLI session

help

none

Displays CLI
command prompts

ping

<value>

IP address

none

repeat

<value>

int:1-4294967295

none

The number of
outgoing icmp echo
requests (default: 5)
5)

payload

<value>

int:0-65535

none

Size of data block (in
bytes) transmitted
by one icmp packets
as payload data
(default:56)

df-bit

none

don't fragment bit
setting (default: not
set)

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды