Eltek Valere Flatpack2 Скачать руководство пользователя страница 29

Страница: 29 / 30

Installation Guide

Flatpack2 -48V 150A

~ 2029242 R2, May 2008

Startup Checklists

This section includes basic checklists to assist the user in verifying proper
installation and starting system operation.

Pre-Start Check

Power is OFF

CHECK THE FOLLOWING POINTS

Flatpack2 system installation is completed; The

Flatpack2 Installation Check List

is filled in.

All cabling is securely terminated with

correct polarity

All battery and load Breakers / fuses are disconnected

AC input cable(s) and AC earth wire (Ground) are terminated

Site specific parameters and settings are known

AC supply and all Breakers / fuses are switched OFF

Start-up, No-Load & Load Adjustments

Power is ON

CARRY OUT FOLLOWING

Install all rectifier modules in desired locations

Verify AC input voltage is correct;

Measure and verify

Switch ON the external AC feeds

Verify all rectifier modules are working, Green power LEDs are ON

Verify

Verify The

Smartpack

is functioning Green power LED is ON

Verify

Connect a PC to the PS system

Install the

PowerSuite

software, if required

Verify DC output voltage;

Measure and adjust as needed

Measure battery voltage, confirm level, and close disconnect if present Verify correct

polarity!

Verify System Setup is in accordance with desired configuration

Enter site spec.
info in

PowerSuite

10.

Connect all load Breakers / fuses, and verify no alarms are displayed

11.

Verify the rectifiers output current, and load function

12.

Verify System Alarm Setup is in accordance with desired configuration Configure alarm

mapping in
PowerSuite

13.

Use PowerSuite to simulate Alarm Relay conditions

Verify all alarm
relays are
working correctly

14.

This completes the basic system start-up and configuration

Содержание Flatpack2































Результаты поиска

Содержание Flatpack2

Отзывы:

Похожие инструкции для Flatpack2

Бренды по названию

Популярные бренды

Eltek Valere Flatpack2, Руководство по установке

Результаты поиска

Содержание Flatpack2

Отзывы:

Похожие инструкции для Flatpack2

Бренды по названию

Популярные бренды