Elsys EMS Door Скачать руководство пользователя страница 15

 

15 

Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden 
E-mail

[email protected]

 

ǀ

 Web

www.elsys.se

 

Caution 

This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 

(1) This device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired 
operation. 

This device and its antenna(s) must not be co-located or operating in 
conjunction with any other antenna or transmitter except in accordance with FCC 
multi-transmitter product procedures. 
 

Industry Canada Statement 

This device complies with Industry Canada license-exempt RSS standard(s). 
Operation is subject to the following two conditions: 

(1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may 
cause undesired operation of the device. 
 

Declaration of conformity 

Hereby, Elektroniksystem i Ume

å

 

AB declares that ERS complies with the 

essential requirements and other relevant provisions of Directive 1999/5/EC. 

Содержание EMS Door
















Отзывы: