Elston Manufacturing GA-700H Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

Elston Manufacturing GA-700H Скачать руководство пользователя страница 15

Using Your Gopher Getter

12

In areas such as pasture:



Tunnel depth of approximately 4 to 5 inches is recommended

In alfalfa fields:



Adjust the coulter as deep as possible while keeping the bottom of the coulter blade at minimum
¼” or so below the bottom edge of the torpedo tube as shown in Figure 14.

Figure 14: Coulter blade depth for treatments in alfalfa

Depending on your exact conditions, the depth may need to be varied somewhat from these
recommendations.

To adjust the depth of the coulter blade, loosen the bolt on the coulter clamp and slide the coulter up or
down on the coulter shank. Lock the coulter clamp when the desired position is found. For larger
adjustments, the bolts that hold the coulter shank to the front of the machine may also be loosened and
the shank slid up or down for further adjustments. Tighten the square headed bolts just tight enough to
hold the shank in position for normal operation (no more than 40 ft-lbf). Over-tightening these bolts will
likely cause one of them to fail when the coulter springs back after an impact with a rock or other
obstruction.

Operating Instructions

The bait used in this machine is highly toxic and can cause serious injury or death
if used improperly. Always follow all precautions on the label for the bait you

use. Store bait as recommended between applications. Do not store bait in the bait
box.

«
...
13
14
15
16
17
...
»

Содержание GA-700H





























Отзывы:

Нет отзывов