Elster Instromet EK205 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 71

background image

50

Operation

6.4.5 Serv. tab (service)

This tab is used to display, check and parameterize special device settings or statuses. The
application is only intended for service technician (specialist staff) or a calibration officer
when commissioning or maintaining.

Display

Meaning

Volume

Submenu for volumes and associated parameters

Volume conversion Submenu for conversion and associated parameters

Measured values

Submenu for analogue measurement values and associated
parameters

Archives

Submenu for archives located in the device

Status

Submenu for current status, status tab and logbooks

Date and time

Submenu for date and time and associated parameters

Batteries

Submenu for device batteries and associated parameters

Inputs

Submenu for the inputs and associated parameters

Outputs

Submenu for all outputs and associated parameters

Interfaces

Submenu for the interfaces in the device

Device settings

Submenu for general device settings

Identification

Submenu for the identification of the gas system

Edit and delete

Submenu for triggering various deletion functions

Examination

Submenu for freezing function and test archive

Data book

Submenu with information from the data book of the device

6.4.6 Strg. tab (control)

This tab is used to check special device settings. The application is only intended for service
technician (specialist staff) or a calibration officer when commissioning or maintaining.

Display

Value

Unit

Access

Address

St.AL

18

Administrator lock: Status / close

-

-

3:170

Cod.A

Enter / change administrator key

-

-

3:171

St.PL

Calibration lock: Status / close

-

-

1:170

Menu

Selection of the display menu

-

C

1:1A1

Main

Content of the Main tab

-

A

2:1A1

18

Operate the device with high communication reliability (high level security, see application manual) so that this menu item is not

displayed.

«
...
48
49
50
51
52
...
»

Содержание EK205








































































Отзывы:

Нет отзывов

Похожие инструкции для EK205

Бренд: Zetec Страницы: 23

Бренд: Unex Страницы: 5

Бренд: Sagola Страницы: 62

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: YOKOGAWA Страницы: 75

LED PowerBank 48

Бренд: SHOWTEC Страницы: 12

Бренд: Twiflex Страницы: 5

Бренд: GAPOSA Страницы: 32

Бренд: Analogue Solutions Страницы: 64

Power System KPS-US

Бренд: Keys Fitness Страницы: 8

Бренд: SDE Lighting Страницы: 7

Бренд: RAB Страницы: 7

Airstream PNEG-362 2000 Series

Бренд: GSi Страницы: 18

Бренд: LIGMAN Страницы: 8

AtLite Sure-Lites SELDWA29SD

Бренд: Eaton Страницы: 4

Бренд: Xils lab Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды