background image

12

9.0 SPARE PARTS

The following comprehensive list of spare parts is available for your Elson EBW25 
water heater. Please refer to the rating label on the right hand side of your heater 
before ordering to ensure the correct spare parts are obtained.

Do not replace with parts not recommended by Elson - this will invalidate your 
guarantee and may render the installation dangerous.

1.   Element assembly (incorporating start dry cutout)............................. 95 607 952
2.   Element assembly sealing gasket........................................................ 95 611 816
3.   Primary cutout (vent pipe)................................................................... 95 612 001
4.  Solenoid valve assembly...................................................................... 95 605 877
5.  Level sensor assembly......................................................................... 95 606 971  
6.  Circuit board  ...................................................................................... 95 615 007
7.  Outlet tap headwork (inc. handle)....................................................... 95 605 071
8.  Outlet tap stem..................................................................................... 95 605 832
9.  Outlet tap cup seal............................................................................... 95 611 731
10. Bezel for tap & cover........................................................................... 95 605 072
11. Cover assy & screws .......................................................................... 95 614 309 

 

12. Condenser sealing gasket ....................................................................95 611 817
13. ‘O’ ring kit........................................................................................... 95 611 002
14. Manifold assy 2.5ltr............................................................................. 95 607 206
15. Outlet spout plastic - tank.................................................................... 95 604 668
16. Outlet spout - cover............................................................................. 95 604 001
17. Push  fi t connector 15x15 straight........................................................ 95 607 509
18. Push  fi t connector 15x15 elbow.......................................................... 95 607 510
19. Tank .................................................................................................... 95 608 926
20. Tank drain & seal................................................................................. 95 608 929
21. Start dry cutout (element).................................................................... 95 612 691
22. Solenoid valve coil.............................................................................. 95 605 839
23. Fitting kit 2.5ltr Model (not pictured)................................................  95 607 024
24. Wiring harness 4-way (not pictured)................................................... 95 612 006
25. Wiring harness complete (not pictured).............................................. 95 607 209

Содержание EBW25

















Отзывы: