elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя | Manualshive

Страница: 36 / 68

background image

34

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

In addition, you can refer to a

slave signal

, i.e. a signal from an additional motion de-

tector, for controlling purposes.

The slave device periodically sends a 1 to the bus, as long as a motion is detected. The
master receives this at the input object "master: slave message" and evaluates the sla-
ve message as an own sensor message.

Furthermore, the master has the possibility of triggering a reset of the slave sending
cycle.

Information on setting the slave sending cycle and the cycle reset can
be found in chapter

Align communication between master and slave

Set the

object type and value

for the master's slave cycle reset output in the same

way, as the cycle reset input for the slave.

The master can be

blocked

via the bus.

6.6.2. Align communication between master and slave

Sending cycle slave - switch-off delay master

Set the slave's

sending cycle

shorter than the master's switch-off delay. Thereby it is

ensured that the master does not perform a switch-off action, while the slave is still de-
tecting a motion.

Slave cycle reset

The cycle reset for the slave is required, if a master switch action by the "master: central
off" object was triggered.

When the master performs a switch-off action, it simultaneously sends a message to
the bus via the "master: slave cycle reset". . This message can be received by the slave

Use slave signal

No • Yes

Slave cycle reset object type

• 1 bit
• 1 byte (0%...100%)

Cycle reset at value

0 • 1 and/or 0...100; 1

Use block

No •

Yes

Analysis of the blocking object

• at value 1: block | at value 0: release
• at value 0: block | at value 1: release

Value prior to first communication

0 • 1

Output pattern

On block

• do not send anything
• Send value

For release

• as for transmission pattern
• send current value immediately

«
...
34
35
36
37
38
...
»

Содержание Mini-Sewi KNX L-Pr





































































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренд: Panasonic Страницы: 2

Бренд: Velocity Страницы: 2

Бренд: SwissPhone Страницы: 2

Бренд: Kayoba Страницы: 44

Бренд: Brickcom Страницы: 40

Бренд: Velleman Страницы: 22

Бренд: Datavideo Страницы: 132

Бренд: Maxocam Страницы: 7

Бренд: Eyeris Страницы: 10

Бренд: SecurityMan Страницы: 13

Бренд: Datavideo Страницы: 92

Бренд: Okina USA Страницы: 31

inelsAir AirSF-100S

Бренд: Elko Страницы: 15

Бренд: Fortinet Страницы: 27

Бренд: Velleman Страницы: 28

Бренд: Encore Страницы: 4

Бренд: Dahua Technology Страницы: 21

Бренд: Idis Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды