elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя | Manualshive

Страница: 28 / 68

background image

26

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

When the

threshold value per parameter

is specified, then the value is set.

When the

threshold value per communication object

is specified, the starting

value, object value limit and type of change to the threshold value are then set.

With both of the methods for specifying the threshold values the hysteresis is set.

Switching output

Define which value the output transmits if the threshold value is exceeded or undercut.
Set the delay for the switching and in which cases the switch output transmits.

Threshold value in kLux

1000 … 150000; 60000

Start threshold value in Lux
valid until first call

1000 … 150000; 60000

Object value limit (min.) in Lux

1000 … 150000

Object value limit (max.) in Lux

1000 … 150000

Type of threshold change

Absolute value • Increase/decrease

Increment in Lux

(upon increase/decrease change)

1000 • 2000 • 5000 • 10000 • 20000

Hysteresis setting

in % • absolute

Hysteresis in % of the threshold value

(for setting in %)

0 … 100; 50

Hysteresis in Lux

(for absolute setting)

0 … 150000; 30000

When the following conditions apply, the
output is
(LV = Threshold value)

• GW above = 1 | GW - Hyst. below = 0
• GW above = 0 | GW - Hyst. below = 1
• GW below = 1 | GW + Hyst. above = 0
• GW below = 0 | GW + Hyst. above = 1

Delays can be set via objects
(in seconds)

No • Yes

Delay from 0 to 1

none • 1 s … 2 h

Delay from 1 to 0

none • 1 s … 2 h

Switching output sends

• on change
• on change to 1
• on change to 0
• on change and periodically
• on change to 1 and periodically
• on change to 0 and periodically

Cycle

(if sent periodically)

5 s ... 2 h

«
...
26
27
28
29
30
...
»

Содержание Mini-Sewi KNX L-Pr





































































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренд: Magnadyne Страницы: 20

Бренд: Barnett Engineering Страницы: 3

Gemini GEM-X255

Бренд: NAPCO Страницы: 40

Бренд: NAPCO Страницы: 16

Бренд: NAPCO Страницы: 6

Бренд: Fastus Страницы: 92

NVIP-2VE-4231/PIR

Бренд: Novus Страницы: 36

Бренд: Takex Страницы: 8

Бренд: SAFE-T-ALERT Страницы: 5

Бренд: DSE Страницы: 20

Бренд: Zavio Страницы: 16

Бренд: ZKTeco Страницы: 55

NVIP-5DN3615AV/IR-1P/F

Бренд: Novus Страницы: 45

TURBO HD H8T Series

Бренд: HIKVISION Страницы: 14

Бренд: Axis Страницы: 25

Бренд: Telepro Страницы: 3

Бренд: XNET Страницы: 17

Бренд: NetMedia Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды