elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя

Страница: 26 / 68

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

Parameter setting

6.1.

Behaviour on power failure/ restoration of
power

Behaviour following a failure of the bus power supply:

The device sends nothing.

Behaviour on bus restoration of power and following programming or reset:

The device sends all outputs according to their send behaviour set in the parameters
with the delays established in the "General settings" parameter block.

6.2.

General settings

Set basic characteristics for the data transfer.

6.3.

Brightness Measurement

The sensor detects the brightness in rooms, for example for controlling lights.

Set the

sending pattern

for the measured brightness.

The brightness reading can be

corrected

in order to compensate for a dull or bright

point of installation for the sensor.

Send delay after reset/bus restoration for:

Measured values

5 s • ... • 300 s

Threshold values and switching outputs

5 s • ... • 300 s

Controller objects

5 s • ... • 300 s

Comparator and logic objects

5 s • ... • 300 s

Maximum telegram rate

• 1 message per second
• ...
• 10 messages per second
• ...
• 50 messages per second

Sending pattern

• never
• periodically
• on change
• on change and periodically

at and above change in %

(if sent on change)

1 ... 100; 20

Send cycle

(if sent periodically)

5 s ... 2 h

Use reading correction

No • Yes

Содержание Mini-Sewi KNX L-Pr





































































Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды

elsner elektronik Mini-Sewi KNX L-Pr, Инструкция по установке и настройке

Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды