elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя

Страница: 10 / 68

Installation and start-up

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

The Sensor is installed surface mounted on the ceiling.

For

capturing movement

make sure that the desired area is covered by the sensor's

coverage angle and that no obstacles obstruct the recording.

When selecting an installation location for

Mini-Sewi KNX TH-L-Pr

, please ensure

that the measurement results of

temperature and humidity

are affected as little as

possible by external influences. Possible sources of interference include:

•

Direct sunlight

•

Drafts from windows and doors

•

Draughts from ducts coming from other rooms or the outdoors

•

Warming or cooling of the building structure on which the sensor is mounted,
e.g. due to sunlight, heating or cold water pipes

•

Connection lines and empty ducts which lead from warmer or colder areas to
the sensor

Measurement variations from such sources of interference must be corrected in the
ETS in order to ensure the specified accuracy of the sensor (offset).

2.2.1. Coverage area of the motion detector

Angle of coverage: approx. 94° × 82°
Range: approx. 5 m

Segmentation of the coverage area

Fig. 1

width

length

Содержание Mini-Sewi KNX L-Pr





































































Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды

elsner elektronik Mini-Sewi KNX L-Pr, Инструкция по установке и настройке

Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды