manualshive.com logo in svg

ELNA eXpressive920, Руководство по обслуживанию, Страница: 62 / 66

Поделиться
Скачать
ELNA eXpressive920 Скачать руководство пользователя страница 62

60

Mechanical Adjustment

n

  Attach the embroidery unit to the MC12000.

 

Insert the machine plug into the power inlet.

 

Insert the power supply plug into the wall outlet and turn 
the power switch on.

10.6±0.5 mm

r

A

B

m

  The embroidery unit carriage position is initialized.

 

The range between A and B should be in the range of  
10.1 mm to 11.1 mm.

 

If the range between A and B is smaller than 10.1 mm, 
loosen the setscrew 

r

 and move the X-sensor position to 

the left.

 

If the range between A and B is larger than 11.1 mm, 
loosen the setscrew 

r

 and move the X-sensor position to 

the right.

 

Initialize the embroidery unit again and be sure the range 
between A and B is in the range of 10.1 mm to 11.1 mm. If 
not, repeat the procedure and adjust the range again.

,

  Tighten the setscrew 

r

 firmly.

y

t

t

y

u

.

 The shielding plate

 

t

 should be positioned at the middle 

of the sensor 

y

 as illustrated.

 

If not, loosen the setscrew 

u

 and adjust the sensor height.

 

Tighten the setscrew 

u

 after the adjustment.

Содержание eXpressive920



































































Отзывы:

Нет отзывов