ELNA eXpressive920 Скачать руководство пользователя

Страница: 43 / 66

Mechanical Adjustment

Presser bar height

To adjust:
1. Turn the power switch ON while pressing the Start/Stop

button and the Reverse stitch button to enter the factory

setting mode.

Press "Foot Up/Down" key.

2. Attach the foot holder lightly (Do not tighten the

thumbscrew.).
3. Press "Down" key. The presser bar will be lowered.

Tighten the thumbscrew firmly.

4. Press “Init” key to initialize the settings. Press “Adjust” key

to lower the foot.

There should be no gap between the foot and needle plate,

but no pressure applied to the needle plate. Check it by

tapping the toe of the foot with fingertip as shown.

5. If there is a gap, press “+” key to lower the foot until the foot

lands on the needle plate without the gap.

6. If the foot depress the needle plate, press “–” key few times

to raise the presser foot, then press “+” key to lower the

foot until the foot lands on the needle plate without the gap.

* Adjust the presser bar height always by pressing “+” key.

Do not press “–” at the end of this adjustment.

* The value of “Adjust Step” should be within the range of

970 to 1030. If the value is far out of the range, check

Automatic Presser Foot Lifter Sensor adjustment.

7. Turn the power itch ON again to enter the ordinary

sewing mode, and set the presser foot pressure to

“Auto-5”. Press the presser foot button to lower the presser

foot. Be sure that there is a clearance between the presser

foot lifter stopper and the automatic presser foot lifter lever

as shown in the picture.

* If there is no clearance between the presser foot lifter

stopper and the automatic presser foot lifter lever, adjust

the presser bar height again.

Clearance

Presser foot lifter stopper

Automatic presser foot lifter lever

Start/Stop button

Reverse
stitch button

⇒

Presser bar

Содержание eXpressive920



































































Результаты поиска

Содержание eXpressive920

Отзывы:

Похожие инструкции для eXpressive920

Бренды по названию

Популярные бренды

ELNA eXpressive920, Руководство по обслуживанию

Результаты поиска

Содержание eXpressive920

Отзывы:

Похожие инструкции для eXpressive920

Бренды по названию

Популярные бренды