ELNA eXperience 520 Скачать руководство пользователя

Страница: 24 / 38

MODEL 520

CORRECT RESULTS

* Beep sounds when the buttons are

pressed.

* Led displays " 8.8", and blinks in 1-

sec. Intervals.

7- segment led displays "Ld" 3 mode

leds blink in 1-sec. Intervals.

* Led indicates "--".

* Button number is displayed when the

button is pressed.

* Led indicates "II".

(At left position)

(At right position)

STEP AND

ITEMS TO

CHECK

01)

7-segment

led

02)

Mode led

03)

Switch

04)

Bobbin

winder

switch

05)

Not

applicable

to this

model

PROCEDURE

Turn on the power switch while

simultaneously pressing the #01

button and the #16 button.

Press the #16 button five times to

select menu item "6".

Press the #01 button: The led

indicates "01" for one second.

If you don't press the #16 button

within 2.5 seconds, the machine

automatically reverts to normal

sewing mode.

Press #01 button, led

displays "02" for one second.

Press #01 button, led

displays "03" for one second.

Press buttons S1 to S3.

Press #01 button, led

displays "04" for one second.

* Move the bobbin winder spindle to

the right.

* Return it to the left.

Skip this step by pressing the #01

button.

DEFECTIVE RESULTS

* No beep sound.

* Does not enter self-diag-

nostic mode.

* Led does not blink on or

off.

1. Replace board "A".

* Led does not blink.

1. Replace board "A".

* Led display is different

from that shown to the

left.

1. Replace board "A".

* Led display is different

from that shown to the left.

1. Adjust bobbin winder

switch position.

2. Replace bobbin winder

switch.

3. Replace board "A".

LED

SELF DIAGNOSTIC SHEET

Button

S1 S2 S3

Содержание eXperience 520







































Результаты поиска

Содержание eXperience 520

Отзывы:

Похожие инструкции для eXperience 520

Бренды по названию

Популярные бренды

ELNA eXperience 520, Руководство по обслуживанию

Результаты поиска

Содержание eXperience 520

Отзывы:

Похожие инструкции для eXperience 520

Бренды по названию

Популярные бренды